Origami Flowers

How to fold an origami step by step?

How to fold origami step by step: get a square, make sharp creases, learn valley and mountain folds, read diagrams, and fold an easy first model.

On this page
  1. The short answer
  2. Step 1: Start with a square
  3. Step 2: Learn to make a clean crease
  4. Step 3: Know valley and mountain folds
  5. Step 4: Read origami diagrams
  6. Step 5: Learn a few bases
  7. Step 6: Fold a first model
  8. When a step doesn’t look right
  9. What to fold next

The short answer

To fold origami step by step, start with a square of thin paper and work on a flat, hard surface. Follow the instructions one step at a time, lining up corners and edges exactly before you press each crease firmly. Most models use two basic folds, valley and mountain, plus a handful of standard starting shapes called bases. Learning those, and the symbols used in diagrams, makes almost any beginner instructions easy to follow.

Step 1: Start with a square

Most origami models start from a square. Origami paper (kami) comes pre-cut in squares, often 15 cm (6 inches). It’s thin, holds creases well, and is usually colored on one side, which makes instructions easier to follow.

If you only have rectangular paper, such as A4 or letter, you can make a square:

  1. Fold one top corner down diagonally so the top edge lines up exactly with the opposite side edge.
  2. Crease the diagonal firmly.
  3. Cut or carefully tear off the leftover strip below the triangle.
  4. Unfold the triangle. You have a square with one diagonal crease.

Printer paper is thicker than origami paper, so it suits simple models better than models with many layers.

Step 2: Learn to make a clean crease

Good creases matter more than anything else in origami.

  • Line up first, crease second. Bring the corner or edge exactly to where it should go and hold it in place with one hand.
  • Crease from the middle outward. Press down in the center of the fold, then slide your finger toward each end.
  • Sharpen it. Run a fingernail, or the side of a pen, along the crease to make it crisp.
  • Work on a table. A hard surface gives much sharper creases than folding in the air or on your lap.

Step 3: Know valley and mountain folds

Almost every fold is one of two types:

  • Valley fold: the paper folds toward you, so the crease forms a “V,” like a valley.
  • Mountain fold: the paper folds away from you, so the crease forms a ridge, like a mountain. You can also make a mountain fold by turning the paper over, making a valley fold, and turning it back.

Many steps say “crease and unfold.” That means you make the fold, press it, and open it again. Those creases act as guides later, so don’t skip them.

Step 4: Read origami diagrams

Origami diagrams use a fairly standard set of symbols. Exact styles vary between books and websites, but these are common:

  • Dashed line: valley fold.
  • Dash-dot line: mountain fold.
  • Thin solid line: an existing crease.
  • Arrow: shows which part moves and where it goes. A curved arrow with a split or open tail often means “fold and unfold.”
  • Looping arrow: turn the paper over.
  • Circular arrow: rotate the paper on the table.
  • Zigzag arrow or “push” arrow: often marks a squash fold or a sink.

It also helps to look one step ahead. The next picture shows what your model should look like once the current step is done.

Step 5: Learn a few bases

Many models start from the same few shapes. Knowing them saves time, and instructions often just say “start with a preliminary base.”

  • Kite base: two edges folded to a diagonal crease, making a kite shape. Used for stems, birds and more.
  • Blintz fold: all four corners folded to the center. The origami lotus uses it repeatedly.
  • Preliminary (square) base: the square collapses into a smaller, layered square. It’s the start of the crane and the origami lily.
  • Waterbomb (triangle) base: the same creases collapsed the other way, into a layered triangle. It’s the start of the 3D origami tulip.

Step 6: Fold a first model

A flat tulip is a good first model because it uses only valley folds:

  1. Fold a square in half corner to corner, with the colored side out, to make a triangle.
  2. Place the long edge at the bottom.
  3. Fold the bottom-left corner up at a slant so its tip pokes out beside the top point.
  4. Do the same with the bottom-right corner.
  5. Turn it over. You have a tulip bloom.

Our guide to origami flowers for beginners covers this tulip in more detail, including a folded stem and leaf, plus a progression of 3D flowers to try next.

When a step doesn’t look right

  • Go back one step. Most mistakes happen a step or two before you notice them. Unfold to the last point where your model matched the picture.
  • Check for “turn over.” Missing a turn-over symbol is one of the most common reasons a model stops matching.
  • Check fold direction. A valley folded as a mountain (or the reverse) can make the next step impossible.
  • Rotate the paper. It doesn’t need to face exactly the same way as the diagram. Turn it so the fold feels natural for your hands, then compare with the picture.
  • Try a fresh sheet. Paper that has been folded and unfolded many times gets soft and loses accuracy.

What to fold next

Once a few simple models feel comfortable, flowers are a satisfying next step. Try the easy origami rose, then the lotus and lily. When you have a few, group them into an origami flower bouquet.

The complete guide to origami flowers

Origami Flowers Step by Step for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →