The traditional origami lotus (sometimes called a water lily) is unusual because it uses almost only one kind of fold: corners folded to the center. The tricky part comes at the end, when you pull the hidden flaps out from underneath to form the petals. This guide explains that stage carefully, because it’s where most first attempts go wrong.
If you’re completely new to folding, the beginner’s guide to origami flowers starts with simpler models and explains the basic terms.
What you need
- One square of paper. A 15 cm (6 inch) square is the smallest size most people find comfortable. A 20 to 25 cm square is easier for a first attempt, because the lotus stacks many layers in a small area.
- Thin paper. Standard origami paper works. Thicker paper, including most printer paper, tends to tear when you pull out the petals. Foil-backed origami paper holds the petal shape well, but it shows every mistake.
- Paper color: Paper that’s the same color on both sides gives a clean, single-color flower. Duo paper (a different color on each side) gives petals with a contrasting inner color, which many people like for a lotus.
Step by step: fold the lotus base
- Crease the diagonals. Fold the square in half corner to corner, unfold, then fold along the other diagonal and unfold. The crossing point marks the center.
- Fold all four corners to the center. This is called a blintz fold. Line each corner up exactly with the center point before you press the crease. You now have a smaller square.
- Fold the four new corners to the center again. This is the second blintz. The square gets smaller and thicker.
- Turn the paper over.
- Fold the four corners to the center a third time. Press firmly, because this layer is thick. Hold the center points down with a fingertip as you work so they don’t spring up.
Some versions add another blintz before turning the paper over, which gives an extra ring of petals. That needs larger or thinner paper, so try the basic version first.
Step by step: pull out the petals
Keep the side you folded last (in step 5) facing up. That side becomes the top of the flower, and the four points meeting in the middle form its center.
- Hold the center firmly. Press down on the middle with one finger, or pinch it from both sides, so the top layer stays in place.
- Find the first flap underneath. Turn the model slightly so you can reach under one corner. On the back, there’s a flap whose tip sits at the center of the back side.
- Pull it out and around. Gently pull that flap’s tip up and around the corner so it wraps toward the top side and stands up as a petal. Ease it out a little at a time rather than in one tug.
- Repeat on all four corners. You now have four petals standing around the center.
- Pull out the next layer. Look underneath again. Between the first four petals there are more flaps tucked away. Pull each one out the same way to make a second ring of four petals.
- Pull out the final layer. One more set of flaps remains on the back. Pull these out so they lie flatter, as an outer ring or base. If you used duo paper, this ring often shows the other color.
If a flap resists, don’t force it. Push it from the back with a fingertip while gently pulling from the front, so the paper slides out instead of tearing.
Shaping and finishing
- Cup the inner petals. Gently pinch the base of each inner petal so it curves upward around the center.
- Spread the outer ring. Press the outermost layer down and out so the lotus sits flat on a table.
- Even it out. Look at the lotus from above and nudge any petals that lean, so the rings look balanced.
Troubleshooting
- The paper tears when I pull the petals. The paper is too thick or too small for this model. Switch to thinner paper or a larger square, and pull more slowly, supporting the flap from behind.
- The flaps won’t come out. Make sure you’re pulling from the back (the side folded twice), not the side you folded last. The center may also be pressed so tightly that the layers are stuck. Loosen it slightly with a fingertip.
- The center keeps opening. Hold it more firmly while pulling. Some folders put a tiny dot of glue under the center points once the lotus is finished.
- It looks lopsided. This usually comes from corners that didn’t meet the center exactly in one of the blintz steps. Small offsets build up, so precise early folds matter more than anything at the end.
Variations
- Extra petals: Add a fourth blintz before turning the paper over (step 4), using larger paper. You’ll have more flaps to pull out and a fuller flower.
- Leaf base: Fold a second lotus from green paper, or simply cut a green circle with a small notch, and glue your colored lotus on top.
- Lotus on a stem: Glue a green paper circle under the lotus and attach a skewer or rolled paper stem to it. This lets you include the lotus in a paper flower bouquet.
Using your lotus
A lotus sits nicely on a table on its own, floats on a dry tray as a centerpiece, or holds a battery tea light in the center. (Don’t put a real candle in it, because the paper can catch fire.) It also pairs well with layered flowers like the easy origami rose, which uses a similar base with different shaping.