The traditional origami tulip is a two-piece model: a 3D bloom that you inflate by blowing into it, and a separate stem with a leaf. Neither piece is hard. The bloom uses one base and a simple locking tuck, and the stem is a series of edge-to-center folds. That makes it a good step up once you’ve folded a flat flower from our origami flowers for beginners guide.
What you need
- One square for the bloom. A 15 cm (6 inch) square of origami paper is a good size. Red, pink, yellow and purple all look tulip-like.
- One square of green paper for the stem. The same size as the bloom square, or slightly larger, usually gives good proportions.
- Optional: a small dab of glue to keep the bloom on the stem.
Origami paper (kami) works best for the bloom because it’s thin enough to inflate. Thick paper resists puffing up and can crumple instead.
Fold the tulip bloom
Make the waterbomb base
- Crease the diagonals. With the colored side up, fold the square corner to corner in both directions, unfolding after each one.
- Crease the middles. Turn the paper over so the white side is up. Fold it in half edge to edge in both directions, unfolding after each one.
- Collapse into a triangle. Hold the paper by two opposite edge midpoints and push them inward. The paper should fold along the existing creases into a layered triangle, with two flaps on the front and two on the back. This is the waterbomb base. Place it with the long open edge at the bottom and the point at the top.
If the paper won’t collapse neatly, check that the diagonal and middle creases go in opposite directions. Re-crease them if needed.
Fold the flaps and lock them
- Fold the front corners up. Take the bottom-left corner of the front layer and fold it up to the top point. Do the same with the bottom-right corner. The front now looks like a diamond.
- Turn over and repeat. Fold the two bottom corners on the back up to the top point too. The whole model is now a diamond.
- Overlap the side flaps. On the front, fold the right flap across toward the left so its corner goes a little past the center line. Then fold the left flap across to the right and tuck its corner into the pocket of the right flap. This locks the two flaps together.
- Turn over and repeat the overlap and tuck on the back.
The tuck takes a little wiggling. Open the pocket slightly with a fingertip, slide the corner in, and press flat.
Inflate and open the petals
- Find the small hole at the bottom point of the bloom.
- Blow gently into it. The bloom should puff up into a rounded 3D shape. If blowing isn’t practical (with a group of children, for example), push a pencil eraser or chopstick gently into the hole and shape the bloom from the inside.
- Peel the petals. At the top there are four pointed flaps. Gently peel each one outward and down a little to open the tulip. Peel them only slightly for a bud, or further for an open bloom.
Fold the stem and leaf
- Crease a diagonal. Place the green square as a diamond and fold it in half from the top corner to the bottom corner, then unfold.
- Kite fold. Fold the two lower edges in to meet the center crease.
- Fold the other end. Fold the two upper edges in to meet the center crease as well, so you have a long, narrow diamond.
- Narrow it again (optional). For a slimmer stem, fold the edges at one end in to the center a second time.
- Fold in half across. Fold the bottom point up to meet the top point.
- Fold in half lengthwise along the center so the model becomes a narrow stalk.
- Pull out the leaf. Hold the folded bottom and gently pull the inner flap away from the outer one, so it angles out to the side. Press the base firmly so the leaf stays at that angle.
Join the bloom to the stem
Slide the pointed top of the stem into the hole at the bottom of the bloom. The fit is usually snug enough to hold for display. If you’ll be moving it around, add a small dab of glue on the tip of the stem before inserting it.
Troubleshooting
- The bloom won’t inflate. Make sure the side flaps are locked (one tucked into the other) on both sides. If the paper is thick, it may need more help: shape it from the inside with a chopstick.
- The bloom puffs up unevenly. Squeeze it gently from opposite sides to even it out, then blow again.
- The petals tear when peeling. Peel slowly from the base of each petal rather than pulling on the tip.
- The stem flops over. Use a slightly larger green square, sharpen all the creases, or slide a thin wooden skewer inside the folded stem.
Variations
- Flat tulip: For cards and young children, the flat tulip in our beginner flowers guide uses only valley folds and no inflating.
- Skewer stem: For bouquets, skip the paper stem and push a thin wooden skewer or green florist wire into the bloom. Fold a separate leaf and glue it on. Our origami flower bouquet guide covers stems in more detail.
- Two-tone tulip: Fold the bloom from duo paper. When you peel the petals down, the inner color shows.
Using your tulips
Tulips are one of the easiest flowers to fold in quantity, so they make a good backbone for a paper flower bouquet. A few tulips on stems also stand well in an origami vase. For contrast, mix them with layered flowers like the origami lily.