Origami Flowers

How to Fold an Origami Lily

Fold a traditional origami lily from one square: preliminary base, squash folds, petal folds, then narrow and curl the petals. Step by step with tips.

On this page
  1. What you need
  2. Step by step: the traditional origami lily
  3. Tips and common problems
  4. Adding a stem
  5. An easier option: the calla lily cone
  6. Using your lilies

The traditional origami lily is a classic intermediate model. It uses the same early steps as the origami crane: a preliminary base, squash folds and petal folds. It then narrows the flaps into four long petals that curl outward. It takes a little more patience than a tulip, but nothing in it is truly difficult once you understand the petal fold.

If you haven’t folded before, the flat tulip in our beginner’s guide to origami flowers is a gentler place to start.

What you need

  • One square of paper, 15 cm (6 inch) or larger. Your first lily will be easier with a bigger sheet.
  • Thin origami paper. The lily stacks many layers at its base, so thick paper makes the last steps hard to fold neatly.
  • Duo paper, if you have it. The inside of the petals shows once they’re curled, so a sheet with a different color on each side gives an attractive two-tone flower.
  • A pencil or skewer for curling the petals.

Step by step: the traditional origami lily

Fold a preliminary base

  1. Crease the middles. With the colored side up, fold the square in half edge to edge in both directions, unfolding after each one.
  2. Crease the diagonals. Turn the paper over. Fold it corner to corner in both directions, unfolding after each one.
  3. Collapse. Hold two opposite corners and bring them together. The paper should fold along the creases into a small, layered square, with two flaps on each side. This is the preliminary base, also called the square base.
  4. Position it with the open corners pointing toward you and the closed point (the center of the original sheet) at the top.

Squash all four flaps

  1. Lift one flap so it stands straight up from the model.
  2. Open it by pushing a fingertip into the pocket.
  3. Press it flat so its center crease lines up with the center of the model. The flap becomes a kite shape lying on top. That’s a squash fold.
  4. Repeat on the other front flap, then turn the model over and squash the two flaps on the back.

When you’re done, the model looks like a diamond with four kite-shaped sections.

Petal fold all four sides

The petal fold is the key step. Take it slowly the first time.

  1. Fold the lower edges in. On the front kite, fold the lower left and lower right edges of the top layer in to meet the center line. Crease firmly.
  2. Fold the top down. Fold the small triangle at the top down over those flaps, crease firmly, then unfold the triangle and both side flaps. You now have creases to guide you.
  3. Lift the bottom point. Take the bottom point of the top layer only and lift it up, using the horizontal crease from step 2 as a hinge.
  4. Let the sides fold in. As you lift, the sides should fold inward along the creases from step 1. Press everything flat. You now have a long, narrow diamond flap on top.
  5. Repeat on the other three kites. To reach each one, fold the flaps like turning pages in a book, or turn the model over.

The finished shape is called a frog base.

Narrow the petals

  1. Check the orientation. The lily’s four petals come from the four corners of the original square, and the base of the flower is the center of the square. Arrange the model so that all four loose corner tips point up. If any flaps point down, fold them up so all four tips sit at the top.
  2. Show a smooth face. Turn flaps like book pages until the face toward you is smooth, with no split down the middle. Do the same on the back.
  3. Fold the lower edges in. On the front, fold the lower edges of the top layer in to meet the center line. This narrows the base of the petal into a slim shape.
  4. Repeat on all four sides, turning pages as needed so each smooth face is in front when you fold it.

The model should now be long and slender, with a narrow closed point at the bottom and four petal tips at the top.

Open and curl the petals

  1. Fold each petal down. Fold the top point of the front petal down as far as it will go. Turn a page and fold down the next one. Repeat until all four petals are folded down.
  2. Curl the petals. Wrap each petal gently around a pencil or skewer, from its tip toward the base, so it curls outward.
  3. Shape the center. The narrow points left standing in the middle form the center of the flower. Pinch them gently so they stand up straight.

Tips and common problems

  • The petal fold won’t lie flat. Your creases from step 1 of the petal fold are probably not sharp enough, or the edges didn’t meet the center line exactly. Unfold, re-crease and try again.
  • The base is bulky and hard to fold. That’s normal for a lily, because many layers meet at the bottom. Use thinner or larger paper, and press each crease firmly before moving on.
  • One petal is longer than the others. This usually starts in the preliminary base, if the collapse was slightly off-center. Check that all corners line up before you begin the squash folds.
  • The petals uncurl. Curl them more tightly, or hold each petal around the pencil for a few seconds before releasing it.
  • You’re stuck on a step. Written steps can only go so far with the petal fold. If you’re stuck, compare your model with a photo or diagram of a frog base. Once you’ve seen the shape, the steps make sense.

Adding a stem

The bottom point of a lily is a natural attachment spot. Snip a tiny amount off the very tip to make a small opening, then push in a green-wrapped skewer or a length of florist wire with a dab of glue. You can also fold a separate stem with a leaf using the method in our origami tulip with stem guide. Insert its point into the base of the lily.

An easier option: the calla lily cone

For young children, a simple calla lily is a good alternative. It’s more of a paper craft than pure origami. Roll a square of white or colored paper into a cone, with one corner wrapping around to form the open, flared top. Glue the overlap, then push a yellow paper strip or pipe cleaner into the center as the spadix, and add a green stem. It takes a few minutes and needs no special folds.

Using your lilies

Lilies have long, spreading petals, so they stand out in a mixed arrangement. Put two or three among rounder flowers like tulips in an origami flower bouquet, or stand them on stems in an origami vase. Because the lily teaches the petal fold, it’s also a good bridge to other intermediate origami.

The complete guide to origami flowers

Origami Flowers Step by Step for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →