Origami Basics

How to Cut a Square from A4 or Letter Paper for Origami

Turn A4 or letter paper into an origami square in a minute: fold-and-cut, tear and ruler methods, exact sizes, and how to use the leftover strip.

On this page
  1. Quick answer
  2. What size square you get
  3. Method 1: Fold and cut
  4. Method 2: Fold and tear (no scissors)
  5. Method 3: Measure and cut with a ruler
  6. How to check your square
  7. Making smaller squares
  8. Using the leftover strip
  9. Tips for folding printer paper

Quick answer

To make a square from A4 or letter paper, fold one corner down so the short top edge lies along one long side, forming a triangle. Crease firmly, then cut or tear off the rectangular strip below the triangle. Unfold the triangle and you have a square with a diagonal crease across it.

It takes under a minute and needs nothing more than the paper and, ideally, scissors.

What size square you get

The square’s side equals the short side of the sheet.

Paper Sheet size Square Leftover strip
A4 210 × 297 mm 210 × 210 mm 87 × 210 mm
US letter 8.5 × 11 in 8.5 × 8.5 in 2.5 × 8.5 in

Both squares are larger than the common 15 cm (6 in) origami paper, which makes them comfortable to learn on.

Method 1: Fold and cut

  1. Lay the sheet flat in portrait orientation (tall, not wide).
  2. Fold the top left corner down and across so the top edge lines up exactly with the right-hand edge. You now have a triangle at the top with a single-layer rectangle below it.
  3. Check that the edges are flush and the triangle’s point sits exactly on the right edge, then crease firmly along the fold.
  4. Cut along the bottom edge of the triangle to separate the rectangular strip below it.
  5. Unfold the triangle. You have a square with a diagonal crease.

The diagonal crease is rarely a problem — many models start by folding the diagonal anyway.

Method 2: Fold and tear (no scissors)

  1. Make the triangle fold as in steps 1–3 above.
  2. Fold the rectangular strip back and forth along the triangle’s lower edge a few times, creasing hard each time. This weakens the paper along the line.
  3. Hold the triangle flat on the table with one hand and tear the strip away slowly, keeping your pulling hand close to the crease.

Alternatively, slide a butter knife or the edge of a ruler into the fold and slice along it. Torn edges are slightly rougher than cut ones, but they are fine for practice and simple models.

Method 3: Measure and cut with a ruler

If you want a square without a diagonal crease, or squares of a particular size:

  1. Measure the short side along the long edge — 210 mm on A4, 8.5 in on letter — and mark it on both long edges.
  2. Join the marks with a straight line.
  3. Cut along the line with scissors, or with a craft knife and metal ruler on a cutting mat. Always cut away from your body.

A paper trimmer gives the cleanest results if you need many identical squares, which is useful for modular origami. Our guide to what tools are needed for origami covers cutting tools in more detail.

How to check your square

Fold the square in half along the diagonal that is not already creased. If all the edges line up exactly, it is square. If one edge sticks out, trim the overhang a little at a time and check again.

A slightly uneven square makes later folds drift, so it is worth getting this right before you start a model.

Making smaller squares

  • Quarters: fold your square in half edge to edge both ways and cut along the creases. A4 gives four squares of 105 mm, and letter gives four squares of 4.25 in.
  • From the leftover strip: the A4 strip (87 × 210 mm) gives two 87 mm squares with a narrow piece left over. The letter strip (2.5 × 8.5 in) gives three 2.5 in squares with a 1 in piece left over. Use the same fold-and-cut method on the strip.

Small squares like these suit modular units and tiny decorations, but they are fiddly for first attempts.

Using the leftover strip

  • Fold small squares for modular origami or practice.
  • Make a simple bookmark by folding the strip in half lengthwise.
  • Use it as scrap stuffing, for example under the top bun of a paper burger.
  • Some origami models are designed for strips or rectangles, so keep a few spares.

A4 paper also has a long-side to short-side ratio of about 1.41 (the square root of 2), which some designers use for models made from the whole rectangle.

Tips for folding printer paper

  • Expect it to feel thicker than origami paper. Models with many layers can get bulky, so start with simpler designs.
  • Crease firmly with a fingernail or folder, as printer paper springs back more than kami.
  • Avoid folding the same line many times, which can crack the paper.
  • Use the whole sheet for rectangle models, such as the paper hat and boat in our guide to easy origami for beginners.

For a full comparison of paper types, see our guide to origami paper and tools.

The complete guide to origami basics

Easy Origami for Beginners: Simple Paper Projects to Start With
Read the guide

Keep exploring

Guides from other topics

All topics →