Origami Animals

How to Fold an Origami Rabbit Step by Step

How to make an origami rabbit: an easy bunny face with adjustable ears, a sitting bunny body, the inflatable waterbomb bunny, and Easter ideas.

On this page
  1. What you need
  2. Easy origami bunny face, step by step
  3. Adjusting the ears
  4. A sitting bunny (face plus body)
  5. The traditional inflatable bunny
  6. Easter and spring ideas
  7. Troubleshooting
  8. FAQ

The easiest origami rabbit is a bunny face. Fold a square into a triangle, fold a strip up from the bottom, then fold the bottom corners up so they become two tall ears. Turn it over, fold the top point down, and draw the face. It takes about five minutes. Below you’ll find the full steps, ways to adjust the ears, a sitting bunny with a body, and notes on the traditional inflatable bunny.

What you need

  • One square of paper for the face, plus a second square if you want a body. A 15 cm (6 inch) square is a good size. White, pink, gray and brown all suit a rabbit.
  • A marker for the eyes, nose and whiskers.
  • Optional: glue or tape, and a cotton ball or a small circle of white paper for a tail.

Easy origami bunny face, step by step

  1. Fold a triangle. Place the square colored side down as a diamond. Fold the bottom corner up to the top corner. The folded edge is now along the bottom and the point is at the top.
  2. Crease the center. Fold the triangle in half from left to right, crease, and unfold.
  3. Fold up the bottom strip. Fold the bottom edge up by about a quarter of the triangle’s height. This strip makes the base of the ears and gives the face a flat chin.
  4. Fold up the ears. Fold the bottom-left corner up along a line that starts at the middle of the bottom edge, so the bottom edge lines up with the center crease. Repeat on the right. The two flaps now point up side by side, with their tips at the top of the model. These are the ears.
  5. Turn over. The ears are behind the face.
  6. Fold the top point down. Fold the top point down, catching only the face layers, not the ear flaps behind. The ear tips now stick up above the head. The further down you fold, the longer the ears look.
  7. Shape the chin. Fold the bottom point up slightly so the chin is rounded.
  8. Draw the face. Add two eyes, a small nose, a mouth and a few whiskers. Pink cheeks or a pink line inside each ear are a nice touch.

Adjusting the ears

  • Longer ears: fold the top point further down in step 6. The ear tips don’t move, but more of each ear shows above the head.
  • Ears that splay apart: in step 4, stop each fold slightly short of the center crease so the ears lean outward a little.
  • Floppy ears (lop-eared bunny): fold the tip of one or both ears down so they bend at the top.
  • Narrower ears: fold the outer edge of each ear behind slightly after step 6.

If one ear ends up taller than the other, the folds in step 4 probably started at slightly different points. Unfold and line both up with the center crease.

A sitting bunny (face plus body)

For a bunny that sits up, fold a simple tent-shaped body from a second square and attach the face to it. The body is the same one used in our easy origami cat guide:

  1. Fold the second square in half diagonally, then in half again into a smaller triangle.
  2. Hold it with the long loose edges at the bottom and the square corner at the top.
  3. For a rabbit, skip the long tail. Instead, fold the back bottom point up behind (or inside) to round off the back.
  4. Open the bottom edges slightly so the body stands.
  5. Glue or tape the face to the top front corner.
  6. Add a cotton ball or a small paper circle at the back as a fluffy tail.

The traditional inflatable bunny

There is also a well-known traditional rabbit built on the waterbomb base, the same base used for the waterbomb balloon. One side of the base is folded into the body, much as in the balloon. The corners on the other side are folded up and out to become two ears. You finish by blowing into a small hole at the bottom, which puffs the body out into a rounded 3D rabbit.

It has more steps than the face, and the waterbomb base needs some practice, so it’s a good second rabbit once you’re comfortable with simple folds. Thin origami paper inflates more easily than printer paper.

Easter and spring ideas

  • Egg decorations. Glue small bunny faces, from 7.5 cm squares, onto paper eggs or egg cartons.
  • Cards. Mount a bunny face on folded card, with grass drawn along the bottom.
  • Table settings. Write guests’ names on the back of the face, or attach a sitting bunny to a place card.
  • Garlands. String bunny faces in pastel colors along ribbon.
  • Treat bags. Glue a bunny face to the front of a small paper bag, with the ears sticking up over the top.

Troubleshooting

  • The ears aren’t visible above the head. You may have folded the ear flaps down along with the top point in step 6. Unfold the top point and fold it again, holding the ears back out of the way.
  • The ears are short. Fold the top point further down, or make the bottom strip in step 3 slightly narrower, which leaves more paper for the ears.
  • The face looks too pointy. Fold the bottom point up more in step 7, or fold the side corners behind to round the cheeks.

FAQ

Is the origami rabbit good for beginners?

Yes. The bunny face uses only valley and mountain folds, and the center crease keeps the ears even. Our beginner’s step-by-step origami guide explains the folds if you’re new.

What paper size is best for an origami bunny?

A 15 cm square makes a face roughly the size of a palm. Use 7.5 cm squares for small decorations and 20 cm squares for young children.

What other easy animals can I fold?

The easy origami cat, origami owl and origami fox are all at a similar level. For the full range, see the origami animals guide.

The complete guide to origami animals

Origami Animals: Step-by-Step Models from Easy to Advanced
Read the guide

Keep exploring

Guides from other topics

All topics →