Origami Animals

How to make a simple dragon out of paper?

Two simple ways to make a paper dragon: a crane-based origami dragon from one square, and an accordion-folded dragon puppet that children can make.

On this page
  1. What you need
  2. Method 1: a simple origami dragon from the bird base
  3. Method 2: an accordion paper dragon for kids
  4. Tips for a better-looking dragon
  5. Where to go after a simple dragon
  6. FAQ

There are two easy ways to make a simple dragon out of paper. The first is a pure origami dragon folded from one square, using the bird base (the same base as the traditional crane). You then use reverse folds to shape the neck, head and tail, and angle the wings like a dragon’s. The second is an accordion paper dragon: two long strips folded over each other into a springy body, with a head and tail attached. It’s a classic children’s craft, especially around Lunar New Year.

Choose the origami version if you want a folding challenge. Choose the accordion dragon for young children or a group activity.

What you need

For the origami dragon:

  • One square of thin paper, about 15 to 20 cm (6 to 8 inches) across. Larger paper makes the head easier.
  • A hard, flat surface.
  • Optional: a marker for the eyes.

For the accordion dragon:

  • Two long strips of paper in contrasting colors, about 2.5 to 4 cm (1 to 1.5 inches) wide. Tape shorter strips end to end to make them longer.
  • Card or thick paper for the head and tail.
  • Glue stick or tape, scissors, and markers.
  • Optional: two drinking straws or craft sticks to make a puppet.

Method 1: a simple origami dragon from the bird base

If you’ve folded a crane before, the first eight steps will be familiar.

Fold the bird base

  1. Pre-crease. Start with the colored side up. Fold and unfold both diagonals. Turn over and fold and unfold the paper in half both ways, edge to edge.
  2. Collapse into a square base. Use the creases to bring the corners together so the paper collapses into a smaller square, with the open end pointing toward you. This is called the square base or preliminary base.
  3. Make the kite creases. Fold the lower edges of the top layer in to the center line. Fold the top triangle down over them. Crease well and unfold all three folds.
  4. Petal fold. Lift the bottom corner of the top layer up along the horizontal crease. The sides fold in along the kite creases. Flatten the result into a long diamond.
  5. Repeat on the back. Turn over and repeat steps 3 and 4. This is the bird base: a long diamond with two narrow points at the bottom and two long flaps at the top.

Narrow the neck and tail

  1. Slim the lower points. Fold the lower edges of the top layer in to the center line. Turn over and repeat. The two bottom points are now thin. One will become the neck and the other the tail.
  2. Reverse fold the neck. Inside reverse fold the left thin point up and outward at a forward-leaning angle.
  3. Reverse fold the tail. Inside reverse fold the right thin point up and outward too, but at a lower angle, so the tail sweeps back behind the body.

Shape the head, tail and wings

  1. Make the head. Pre-crease near the top of the neck and inside reverse fold the tip down to form the head. For a longer snout, make the fold a little further from the tip. For a blunter dragon face, add a second small reverse fold at the very end.
  2. Crimp the tail. Make a crimp (two reverse folds close together) partway along the tail so it dips and rises like a dragon’s tail rather than pointing straight out.
  3. Set the wings. Fold the two long flaps down so they stick out to the sides, as you would for a crane, then tilt them upward and back.
  4. Make dragon wings. To make the wings look less like a bird’s, accordion-pleat each one two or three times along its length, then fan the pleats slightly. Alternatively, fold the leading edge of each wing in at an angle so it looks sharper.
  5. Finish. Draw eyes on each side of the head. Gently curve the neck if the paper allows it.

This dragon sits on its belly rather than standing on legs. If you want to try a model with legs, the bird-base T-rex in our origami dinosaur guide turns the wing flaps into legs instead.

Method 2: an accordion paper dragon for kids

This version uses glue and scissors, so it’s a paper craft rather than strict origami. It’s very approachable for young children.

  1. Join the strips. Glue the end of one strip on top of the end of the other at a right angle, so they form an L shape.
  2. Fold them over each other. Fold the bottom strip over the top one so it lies flat along it. Then fold the other strip over that one. Keep alternating, always folding the bottom strip over the top, until you run out of paper. The strips build up into a square stack.
  3. Secure the end. Glue the last two folds together and trim any leftover strip.
  4. Stretch it out. Gently pull the ends apart. The stack opens into a springy, zigzag body.
  5. Make the head and tail. Draw and cut a dragon head and a tail from card. Add eyes, teeth, whiskers or flames with markers or paper scraps.
  6. Attach them. Glue the head to one end of the body and the tail to the other.
  7. Optional puppet. Tape a straw or craft stick under the head and another under the tail, then move them to make the dragon dance.

Red and gold strips give the dragon a festive look for Lunar New Year. Our article on the Chinese New Year origami tiger has more ideas for festive paper decorations.

Tips for a better-looking dragon

  • Use thinner paper for the origami version. The neck and tail have many layers by step 9, and thin paper keeps the reverse folds crisp.
  • Pre-crease every reverse fold. Fold the angle firmly both ways before pushing the point inside.
  • Make the head bigger than a crane’s. Making the head fold further from the tip gives a chunkier, more dragon-like head.
  • Experiment with the tail. Two crimps instead of one give a wavier tail.
  • For the accordion dragon, keep the folds square. Line each fold up exactly with the edge below it so the body stays straight when stretched.

Where to go after a simple dragon

Dragons are also among the most famous complex origami subjects. Satoshi Kamiya’s Ryujin designs, for example, are known for scales, claws and whiskers folded from one sheet, and they demand a lot of time and very thin, large paper. Between a crane-based dragon and models like that, there are many intermediate dragon diagrams in published collections. Most add legs and horns, which call for reverse folds, crimps and some sink folds.

For other models in the same difficulty range, see the origami animals guide. If the bird base was a struggle, try our step-by-step beginner guide first.

FAQ

What is the easiest origami dragon?

Dragons based on the crane are generally among the simplest true origami dragons, because they reuse the familiar bird base and add only a few reverse folds and crimps.

What size paper is best for a paper dragon?

For the origami dragon, a 15 cm square is the minimum and 20 cm is more comfortable. For the accordion dragon, longer strips make a longer, bouncier body.

Is the accordion dragon real origami?

Not strictly, because it uses glue and cut card for the head and tail. The springy body is a folding technique, though, and it’s an easy, satisfying project for children.

The complete guide to origami animals

Origami Animals: Step-by-Step Models from Easy to Advanced
Read the guide

Keep exploring

Guides from other topics

All topics →