Origami Animals

How to Fold an Origami Fox (Face and Full Body)

How to make an origami fox: step-by-step instructions for an easy fox face and a two-piece full-body fox with a white-tipped tail, plus tips for a fox-like look.

On this page
  1. What you need
  2. Origami fox face, step by step
  3. Full-body fox (two-piece): body with a white-tipped tail
  4. Putting the fox together
  5. Making it look more fox-like
  6. Troubleshooting
  7. FAQ

An origami fox is a good next step after your first simple models. The face uses only basic folds. The full-body fox adds one or two reverse folds for the tail. This guide covers both: an easy fox face from one square, and a two-piece sitting fox that joins that face to a simple body with a white-tipped tail.

What you need

  • Two squares of paper, about 15 cm (6 inches). Orange paper with a white reverse is ideal, because the white side can show as the tail tip. Plain orange paper works too; draw the details on.
  • A marker for the eyes and nose.
  • Glue stick or tape to join the face to the body.

Origami fox face, step by step

The fox face starts the same way as a simple cat face. Taller ears and a narrower, pointed muzzle make it read as a fox.

  1. Fold a triangle. Place the square colored side down as a diamond. Fold the top corner down to the bottom corner. The folded edge is at the top and the point faces down.
  2. Crease the center. Fold the triangle in half from left to right, crease, and unfold.
  3. Fold the side corners down. Fold the left and right corners down to meet the bottom point. You now have a smaller diamond, with two flaps on the front that meet along the center crease.
  4. Fold up the ears. Fold the tip of each flap back up so it points upward past the top of the diamond. For a fox, fold the ears so they point mostly straight up, and leave plenty of length showing above the head. This is the main difference from a cat, whose ears angle further outward.
  5. Turn over. The ears are now behind the head, and their tips stick up above it.
  6. Slim the face. Fold the left and right side corners of the diamond behind slightly. This narrows the cheeks toward the bottom point, which becomes the fox’s pointed muzzle.
  7. Flatten the top of the head. If you like, fold the small top corner between the ears down or behind.
  8. Draw the face. Put a small dark nose right at the bottom tip and two eyes partway up. Leave the muzzle pointed rather than folding it up.

Full-body fox (two-piece): body with a white-tipped tail

The body is a simple tent shape that stands on its edges. The tail comes from one corner.

  1. Fold a triangle. Fold the second square in half diagonally with the orange side out.
  2. Fold in half again. Fold the triangle in half corner to corner to make a smaller triangle.
  3. Orient it. Hold it with the long loose edges at the bottom and the square corner at the top. The sloping side that’s a single closed fold is the fox’s back. The sloping side with two separate edges is the chest.
  4. Make the tail. Pre-crease a line across the bottom point at the back end, both ways. Then inside reverse fold the point up between the layers so it sticks out behind the body as a tail. A fox’s tail is long and low, so angle it outward and only slightly upward.
  5. Make the white tip. Pre-crease a short line near the end of the tail, then outside reverse fold the very tip. Wrapping it around the outside turns the paper inside out at the end, so the white side shows as the tail tip.
  6. Stand it up. Open the bottom edges slightly so the body stands.

Putting the fox together

  1. Position the face. Hold the fox face against the top front corner of the body, where the back and chest edges meet.
  2. Attach it. Glue or tape it in place, angling it slightly forward so the fox looks ahead rather than up.
  3. Check the balance. If the face makes the body tip forward, move the face back a little, or fold the face from a smaller square, such as 10 to 12 cm.

The same body works for other animals. Our guides to the easy origami cat and how to make a tiger with origami paper use it with different faces and markings.

Making it look more fox-like

  • Ears: keep them tall and upright. Wide, outward-angled ears make the face look more like a cat.
  • Muzzle: keep the bottom point sharp, and put the nose right at the tip.
  • Color: orange with white is classic. Gray with white makes a gray fox, and white with a black nose suggests an arctic fox.
  • Cheeks: if your paper is orange on both sides, draw a white or cream patch on each side of the muzzle with a paint pen.
  • Tail: a long tail angled low reads as a fox. A tail that points straight up looks more like a cat.

Troubleshooting

  • The ears are different heights. Use the center crease to check that both flaps were folded at the same angle in step 4.
  • The tail tears when reverse folding. Pre-crease more firmly, and open the layers a little wider before pushing the point inside.
  • No white tip shows. Your paper may be orange on both sides. Draw the tip on, or use paper with a white reverse.
  • The body won’t stand. Spread the bottom edges wider, and make sure the tail reverse fold is fully flattened.

FAQ

Is the origami fox easy?

The face is easy and uses only valley and mountain folds. The full-body fox adds an inside reverse fold and an outside reverse fold, which are a common next skill for beginners. Our beginner’s step-by-step origami guide explains both.

What size paper should I use for an origami fox?

A 15 cm square works for both the face and the body. For small children, 20 cm paper is easier to handle.

Can I make a fox from one sheet?

Yes. There are one-piece fox designs, but they are usually more involved than the two-piece version here. For an overview of models by difficulty, see the origami animals guide.

The complete guide to origami animals

Origami Animals: Step-by-Step Models from Easy to Advanced
Read the guide

Keep exploring

Guides from other topics

All topics →