Origami Animals

How to make a tiger with origami paper?

How to make a tiger with origami paper: an easy tiger face, a two-piece standing tiger, tips for drawing stripes, and what to expect from advanced 3D tigers.

On this page
  1. What you need
  2. Easy origami tiger face
  3. Two-piece standing tiger
  4. Adding stripes and details
  5. Advanced 3D tigers
  6. Troubleshooting
  7. FAQ

To make a tiger with origami paper, start with an orange square. Fold it into a triangle, fold the bottom corners up into pointed ears, fold the top point down to flatten the head, then draw on eyes, a nose and black stripes. That’s a tiger face, and it takes about five minutes. For a tiger that stands, fold a second square into a simple tent-shaped body and attach the face to it. Fully 3D one-piece tigers exist too, but they are advanced models with dozens of steps.

This guide covers all three levels.

What you need

  • Paper. One 15 cm (6 inch) square for the face, plus a second square of the same size for the body. Orange is the obvious choice; white paper makes a white (Bengal-style) tiger. Paper that is orange on one side and white or cream on the other gives a pale face or belly where the white shows.
  • A black marker for stripes, plus a finer pen for the eyes and nose.
  • Glue stick or tape to join the two-piece tiger.

Easy origami tiger face

  1. Fold a triangle. Place the square colored side down as a diamond. Fold the bottom corner up to the top corner. The folded edge is now along the bottom and the point is at the top.
  2. Crease the center. Fold the triangle in half from left to right, crease, and unfold.
  3. Fold the left ear. Fold the bottom-left corner up along a line that starts just to the left of the center of the bottom edge. Its tip should end up just to the left of the top point. This flap is the left ear.
  4. Fold the right ear. Repeat on the right so the two ear tips sit side by side, just either side of the top point, at matching heights.
  5. Turn over. The ears are now behind the face.
  6. Flatten the head. Fold the top point down so the top of the head is flat and the ear tips stick up above it. The further down you fold, the taller the ears look.
  7. Shape the chin. If the bottom looks too sharp or too wide, fold the bottom corners behind slightly to round off the jaw.
  8. Draw the face. Add eyes, a triangular nose, a mouth and whisker dots. Then add the stripes (see below).

This face uses the same idea as our easy origami cat. The difference is mostly in the color and markings.

Two-piece standing tiger

The body is a simple tent shape that stands on its raw edges, with the face attached to the front.

  1. Fold a triangle. Take the second square and fold it in half diagonally, colored side out.
  2. Fold in half again. Fold the triangle in half, corner to corner, to make a smaller triangle.
  3. Find the back. Hold it with the long edge (all the loose raw edges) at the bottom and the square corner at the top. One sloping side is a single fold that joins both halves; this is the tiger’s back. The other sloping side has two separate folded edges; this is the chest.
  4. Make the tail. Pre-crease a line across the bottom point at the back end, then inside reverse fold that point up between the layers so it sticks up and out as a tail.
  5. Shape the tail. For a curved tail, add a second, smaller reverse fold near the tip, or curl it gently around a pencil.
  6. Stand it up. Open the two sides slightly at the bottom so the body stands on its edges.
  7. Attach the face. Glue or tape the tiger face to the top front corner of the body, slightly overlapping the chest edge.
  8. Add stripes to the body. Draw a few curved stripes down the sides and a ring or two around the tail.

A face folded from the same size square as the body gives a cute, cartoon look. For more natural proportions, fold the face from a slightly smaller square.

Adding stripes and details

Stripes do most of the work in making the model read as a tiger rather than a cat or fox.

  • Draw on the folded model, or unfold it? On the face, drawing on the finished model is fine. On complex 3D tigers, some folders partly unfold the model to draw the pattern and then refold it, which avoids smudging layers.
  • Stripe shape. Use tapered stripes, thick at one end and thin at the other, in small groups of two or three. Avoid evenly spaced straight lines.
  • Forehead mark. A cluster of stripes on the forehead is a classic tiger feature, and in Chinese tradition it is often drawn to look like the character 王 (“king”). See our Chinese New Year origami tiger for more on that.
  • Test your marker first. Some markers bleed into thin origami paper. Try one on a scrap of the same paper first.

Advanced 3D tigers

One-piece standing tigers with four legs, a head and a tail are intermediate to advanced models. As a reference point, one widely shared 3D tiger tutorial runs to 38 steps and takes about 40 minutes. It turns a 15 cm square into a tiger roughly 8 cm long. Expect several kinds of fold, including pleats, squash folds and reverse folds. For more detailed designs, a 20 cm (8 inch) or larger square gives you more room for thin legs and a long tail.

If you want to build up to these, practise reverse folds on simpler models first. The T-rex in our origami dinosaur guide is a good warm-up.

Troubleshooting

  • Ears are uneven. Make sure the center crease is sharp, and check that both ear folds start the same distance from the center of the bottom edge.
  • Ears are too short. Fold the top point down further in step 6.
  • Body tips over. Spread the bottom edges a little wider, or fold the face from smaller paper so it doesn’t pull the body forward.
  • Marker bleeds. Switch to a fine-tip pen, or use paper with a slightly coated surface.

FAQ

What color paper should I use for an origami tiger?

Orange is traditional. Orange paper with a white reverse lets a pale face or belly show. White paper with black stripes makes a white tiger.

Is an origami tiger good for kids?

The face is suitable for most children who can fold a triangle and match corners. The two-piece tiger adds one reverse fold for the tail, which an adult may need to help with.

What other big cats can I fold the same way?

The same face and body work for a lion if you draw a mane around the face, or for a leopard with spots in place of stripes. For a fox, see our origami fox face and full body guide.

The complete guide to origami animals

Origami Animals: Step-by-Step Models from Easy to Advanced
Read the guide

Keep exploring

Guides from other topics

All topics →