Origami Toys

How to make an easy origami fidget?

The easiest origami fidgets to make, with step-by-step instructions for a two-strip paper spring and a push-pop button, plus flexagons and other quick ideas.

On this page
  1. Quick answer
  2. Easy origami fidgets compared
  3. Paper spring (two-strip accordion), step by step
  4. Push-pop button fidget
  5. Flexagon fidget (trihexaflexagon)
  6. More easy fidgets to try
  7. Tips for fidgets that last

Quick answer

The easiest origami fidget is a paper spring: two strips of paper folded over each other at right angles until you have a springy, squishy accordion. It takes about five minutes and needs only paper and a dot of glue or tape.

If you want something that clicks and pops, try the push-pop button, made from two nested paper boxes with a folded spring inside. It takes about 15–20 minutes. Both are explained step by step below.

Easy origami fidgets compared

Fidget What it does Time Difficulty Paper
Paper spring Stretches, squashes, bounces About 5 min Very easy Two long strips
Push-pop button Presses down and springs back up 15–20 min Easy Three squares
Flexagon Flips to show hidden faces 15–30 min Easy, but needs accuracy A strip or a printed template
Fortune teller Opens and closes in your fingers About 5 min Very easy One square
Jumping frog Hops when you press its back About 5 min Easy Index card or square

Times are rough guides for a first attempt.

Paper spring (two-strip accordion), step by step

You’ll need two long strips of paper of the same width. Strips about 2–3 cm wide and 30 cm or longer work well. You can cut them from the long side of a sheet of printer paper, or tape shorter strips end to end. Two different colors look best. You’ll also need a dot of glue or a small piece of tape.

  1. Make an L. Lay one strip horizontally and the other vertically so their ends overlap in a square, forming an L shape. Glue or tape the overlapping square.
  2. Fold the bottom strip over. Whichever strip is underneath, fold it over the top strip so it lies flat across the square. Crease it.
  3. Keep alternating. Now fold the other strip, which is now underneath, over the top. Keep folding the strips over each other, one then the other, always crossing at right angles and creasing each fold.
  4. Fold to the end. Keep going until the strips run out. Try to keep the stack square and the folds tight.
  5. Lock the ends. Glue or tape the last two squares together and trim any leftover paper.

Hold the ends and stretch it out, then squash it back down. It also bounces if you drop it. Longer strips make a longer, bouncier spring.

Push-pop button fidget

This fidget has a small box base, a paper spring and a slightly larger box on top as the button. Press the button down and the spring pushes it back up. You’ll need three squares:

  • One 12 cm square for the inner box
  • One 14 cm square for the outer box
  • One 20 cm square for the spring

Fold two boxes

Fold a traditional masu box from each of the smaller squares:

  1. Place the square colored side down and crease both diagonals.
  2. Fold all four corners to the center.
  3. Fold the top and bottom edges to the center line and unfold. Fold the left and right edges to the center line and unfold.
  4. Unfold the top and bottom corner flaps, leaving the left and right flaps folded in.
  5. Stand the left and right sides up as walls along their creases.
  6. Raise the top end. Its corners fold in along the existing creases to form the third wall. Fold the top flap over that wall and down into the box, so its point touches the center of the base.
  7. Repeat with the bottom end.

The box from the 14 cm square should slide easily over the box from the 12 cm square. If it’s tight, refold the smaller box from a slightly smaller square.

Fold the spring and assemble

  1. Make a strip. Fold the 20 cm square in half and unfold. Fold the top and bottom edges to the center. Then fold the new top and bottom edges to the center again, and fold the whole thing in half. You’ll have a narrow, multi-layered strip about 2.5 cm wide.
  2. Accordion-fold it. Fold the strip back and forth in short zigzag pleats along its whole length, like a fan. Squash it and let go to check it springs back.
  3. Assemble. Stand the smaller box open side up. Set one end of the spring inside it. Place the larger box upside down over the top of the spring, like a cap.

Press the cap down and release. If it doesn’t rise far, make the spring pleats a little wider or use stiffer paper for the spring.

Flexagon fidget (trihexaflexagon)

A flexagon is a folded paper strip that forms a hexagon. When you pinch and push it in the right way, it “flexes” to show faces that were hidden inside. The simplest, the trihexaflexagon, is made from a strip of equilateral triangles, usually ten, with the last one used as a glue tab. It has three faces, and one of them stays hidden until you flex it.

Accuracy matters with flexagons. The triangles must be truly equilateral, or the hexagon won’t lie flat. A printable template or a strip ruled with a protractor gives the best results. Sticky note versions are popular too, because the notes are a consistent size. Once it works, color each face differently and see if a friend can find the hidden one.

More easy fidgets to try

When you’re ready for a bigger project, the magic ball and the infinity cube are covered in our origami fidget toys guide.

Tips for fidgets that last

  • Use slightly heavier paper for parts that take a lot of pressing, such as the spring. Thin origami paper wears out faster.
  • Crease firmly. Sharp creases make springs bouncier and boxes sturdier.
  • Keep spares of the spring. It’s the part that wears out first, and it only takes a minute to refold.
  • Tape worn joints before they tear right through.

The complete guide to origami toys

Origami Toys: Paper Models That Move and Play
Read the guide

Keep exploring

Guides from other topics

All topics →