Origami Toys

How to Fold an Origami Jumping Frog That Really Hops

Fold an origami jumping frog that really hops: index card steps, the Z-fold spring, launch technique, fixes for frogs that flop, and simple frog race games.

On this page
  1. Which paper makes the best jumper
  2. How to fold an origami jumping frog (index card version)
  3. How to make it jump
  4. Why your frog won’t jump (troubleshooting)
  5. Square-paper version with back legs
  6. Jumping frog games

The origami jumping frog is a traditional model with a built-in spring. Press down on its back, slide your finger off, and it leaps forward or flips through the air. Every frog will hop a little, but a few details make the difference between a frog that shuffles and one that really jumps: stiff paper, sharp creases and a good launch.

Which paper makes the best jumper

The spring works by storing energy in a folded pleat, so stiffer paper jumps better.

Paper How well it jumps Notes
Index card (3 x 5 in) Best Stiff and springy, and already the right shape
Thin card or business card Very good Small cards make small, quick frogs
Printer paper Good Easy to find. Fold it smaller for more spring
Standard origami paper Fair Thin, so the spring is weaker. Fine for practice

The index card version below is a popular choice for that reason. If you only have square origami paper, see the square version further down.

How to fold an origami jumping frog (index card version)

You need one 3 x 5 inch (about 76 x 127 mm) index card. Hold it upright, short edge at the top.

Make the head and front legs

  1. Crease an X at the top. Fold the top-left corner down to the right edge, so the top edge lines up with the right side. Crease and unfold. Then fold the top-right corner down to the left edge, crease and unfold. You’ll see an X near the top of the card.
  2. Crease across the center of the X. Turn the card over. Fold the top down so the crease runs straight across through the middle of the X. Crease well, unfold and turn the card back over.
  3. Collapse into a triangle. Push in at both ends of the horizontal crease. The sides fold in along the X creases while the top folds down, and the top collapses into a triangle sitting on top of the rectangle. Flatten it.
  4. Fold the front legs. Fold the left and right bottom corners of the triangle’s top layer up to the point of the triangle. These small flaps are the front legs. You can angle them out slightly so the frog stands steadily.

Make the body and spring

  1. Narrow the body. Fold the left and right edges of the rectangle below the triangle in to meet at the center line. Their top ends tuck under the triangle.
  2. Fold the body up. Fold the bottom edge up so it meets the base of the triangle, where the head meets the body.
  3. Make the spring. Fold that same flap back down in half, so its edge lines up with the bottom fold. You now have a Z-shaped pleat at the back. This is the spring.
  4. Turn it over. The frog sits on its front legs and the folded spring. Draw eyes on the head if you like.

How to make it jump

  1. Put the frog on a smooth, hard surface, such as a table or a wooden floor.
  2. Place a fingertip on the very back edge of the frog, over the spring.
  3. Press down so the spring flattens.
  4. Slide your finger backward and off the edge quickly. The spring snaps open and launches the frog.

A firmer press stores more energy. A quick, clean slide off the back edge gives the best jumps. Try a few different pressures, because a light press often makes a frog hop forward, and a harder press makes it flip.

Why your frog won’t jump (troubleshooting)

  • It barely moves. The spring creases are too soft. Re-crease both folds of the Z-pleat firmly with a fingernail, or refold on stiffer paper.
  • It slides instead of jumping. You’re pushing it forward rather than pressing down. Press straight down, then slide off the back.
  • It always flips over. Press a little more lightly, or make the spring pleat slightly smaller.
  • It veers to one side. The body folds in step 5 weren’t even. Refold so both edges meet exactly at the center.
  • It worked, then stopped. Springs wear out with use. Refold the Z-pleat, or fold a fresh frog. It only takes a few minutes.
  • The surface is too soft. Carpet and tablecloths absorb the spring. Use a hard surface.

Square-paper version with back legs

If you’re using a square of origami paper, the traditional square frog follows a similar idea, with a few extra steps that give it back legs:

  1. Crease the square in half both ways, and crease diagonal guides at the top as in step 1 above.
  2. Collapse the top into a triangle, then fold up the front legs.
  3. Turn the model around and fold the lower side edges in to the center.
  4. Fold the bottom section up, then pull out and flatten the side pockets to form back legs. Angle the leg tips out.
  5. Fold the lower half up, then fold its bottom edge back down to make the Z-shaped spring, just like the index card frog.

A 15 cm (6 in) square makes a good-sized frog, but origami paper is thinner than card, so expect gentler jumps. Folding two squares together as one, or using a smaller square, makes a stiffer spring.

Jumping frog games

  • Frog race. Line up at a start line, and the first frog across the finish line wins. Only jumps count, not pushes.
  • Long jump. Each frog gets three jumps from the same line, and the longest single jump wins.
  • Target practice. Try to land frogs in a bowl, a paper “pond” or a box lid.
  • Flip contest. See whose frog can do a full flip and land on its feet.
  • Frog factory. Try different sizes and papers, and test which jumps furthest. It’s a nice simple science activity for kids.

For another quick action toy, try a paper fortune teller or a paper ninja star. Fidget fans can head to how to make an easy origami fidget, and the full set of projects is in our origami toys guide.

The complete guide to origami toys

Origami Toys: Paper Models That Move and Play
Read the guide

Keep exploring

Guides from other topics

All topics →