Origami Toys

How to make a card holder out of paper?

Make a card holder out of paper with a no-glue two-pocket fold or a quick sleeve, sized for trading cards, business cards and gift cards. Steps and tips.

On this page
  1. Quick answer
  2. Common card sizes
  3. Two-pocket paper card holder, step by step
  4. Quick single-pocket sleeve
  5. Paper card holder for kids’ card games
  6. Making it sturdier
  7. Are paper card holders safe for valuable cards?

Quick answer

The simplest way to make a card holder out of paper is to fold a strip of paper into a small book with a pocket on each side. You fold the two ends of the strip in to the middle to make the pockets, fold a narrow hem along the top and bottom to close their edges, then fold the whole thing in half. It needs no glue, and one sheet of A4 or US Letter paper gives you a strip big enough for trading cards, business cards or credit cards.

Full steps and sizes are below, along with a quick single-pocket sleeve and a stand for kids’ card games.

Common card sizes

Measure your cards before you cut, because it decides the size of the strip. These are the common standard sizes:

Card Size
Standard trading card (Pokemon, Magic: The Gathering and similar) 63 x 88 mm (about 2.5 x 3.5 in)
Credit card, gift card, ID card 85.6 x 54 mm
US business card 3.5 x 2 in (about 89 x 51 mm)
European business card 85 x 55 mm

Two-pocket paper card holder, step by step

What you need

  • One sheet of A4 or US Letter paper. Thicker paper, such as 100–120 gsm or light card, makes a sturdier holder.
  • A ruler and a pencil
  • Scissors or a craft knife

Steps

  1. Cut a strip. Cut a strip 115 mm (about 4.5 in) wide across the full length of the sheet. From A4 that’s 115 x 297 mm, and from Letter it’s about 115 x 279 mm.
  2. Find the center. Lay the strip horizontally with the side you want on the inside facing up. Fold it in half end to end, crease and unfold.
  3. Make the pockets. Fold each short end in so it meets the center crease. Crease firmly. Each of these flaps forms a pocket, with its opening facing the middle.
  4. Hem the top and bottom. Fold the top long edge down by 1 cm across all the layers, and crease. Do the same with the bottom edge, folding it up by 1 cm. These hems close off the top and bottom of both pockets, so cards can’t slide out the sides.
  5. Close the book. Fold the strip in half along the center crease, with the pockets on the inside.
  6. Add the cards. Open the holder and slide a card into each pocket, under the flap and in from the middle, with the card’s long side running up and down.

With an A4 strip, each pocket is about 74 mm wide and about 95 mm tall inside, which fits a trading card, a credit card or a business card with a little room to spare. With a Letter strip, the pockets are about 70 mm wide.

If the hems spring open, run a fingernail along them, or put a tiny dot of glue under each corner.

Sizing it for other cards

You can work out the strip size for any card:

  • Strip width = the card’s long side + 2 cm for the hems + about 5 mm of slack
  • Strip length = 4 x (the card’s short side + about 5 mm)

For example, a card measuring 60 x 90 mm needs a strip about 115 mm wide and at least 260 mm long. A longer strip just gives you wider pockets.

Quick single-pocket sleeve

For a single card, such as a gift card you’re giving away or one favorite trading card, this sleeve takes about a minute.

  1. Cut a rectangle 100 x 210 mm. The short side of an A4 sheet is 210 mm, so you only need one cut.
  2. Hold it upright and fold the bottom edge up by 60 mm to make a pocket.
  3. Fold the left and right edges to the back by 15 mm each, through all the layers. This closes the sides of the pocket and leaves it about 70 mm wide.
  4. Slide the card into the pocket, standing upright.
  5. Fold the top down over the card, about 95 mm above the bottom fold, and tuck the end of the flap into the pocket to close it.

This fits a standard trading card. Credit cards, gift cards and business cards are narrower than a trading card when stood upright, and no taller, so they fit the same sleeve.

Paper card holder for kids’ card games

Young children often struggle to hold a fan of cards. A pleated stand lets them see their cards without anyone else seeing them:

  1. Take a strip of stiff paper or light card, about 10 cm wide and 30 cm long.
  2. Fold it back and forth into accordion pleats about 1.5 cm deep along its length.
  3. Pull the pleats open slightly and stand the strip on the table, facing the child.
  4. Rest the cards in the valleys of the pleats so they lean back against the next fold.

It works best with stiff card. Thin paper flattens under the weight of the cards.

Making it sturdier

  • Use heavier paper. Light card or thick craft paper holds its shape far better than copy paper.
  • Cover it. Clear self-adhesive film over the outside makes it more durable and water-resistant. Apply it to the strip before folding, then crease firmly.
  • Reinforce the hems with a thin line of glue if the holder will be opened often.
  • Decorate it. Patterned paper, washi tape or a drawn design makes a nice handmade gift.

Are paper card holders safe for valuable cards?

For everyday cards, such as play decks, business cards and gift cards, a paper holder is fine. For trading cards with real value, it’s best to use protection made for the job, usually a soft plastic sleeve, often inside a rigid toploader. Paper can rub the card surface and doesn’t protect against bending or moisture.

If you’re a Pokemon fan, you might also enjoy folding the characters themselves. See origami Pokemon step by step. For more practical and playable folds, visit our origami toys guide.

The complete guide to origami toys

Origami Toys: Paper Models That Move and Play
Read the guide

Keep exploring

Guides from other topics

All topics →