Origami Birds

How to make an origami bird easy step by step?

Make an easy origami bird step by step from one square: fold a triangle, fold it in half, reverse fold the neck and head, and shape the wings.

On this page
  1. The Quick Answer
  2. Before You Start
  3. Step-by-Step Instructions
  4. How to Do the Inside Reverse Fold
  5. Common Mistakes and Fixes
  6. Ways to Change It Up
  7. Next Birds to Try

The Quick Answer

To make an easy origami bird, start with a square of paper and:

  1. Fold it in half diagonally to make a triangle.
  2. Fold the triangle in half again to make a smaller triangle.
  3. Inside reverse fold one sharp point upward to make the neck.
  4. Inside reverse fold the tip of the neck forward to make the head.
  5. Fold the two loose flaps out to the sides as wings.

That’s the whole model. The rest of this page goes through each step slowly, with a checkpoint so you can confirm you’re on track, and explains the one technique beginners usually find tricky: the inside reverse fold.

Before You Start

Paper. Use a square sheet about 15 cm (6 in) on each side. Standard origami paper is ideal, but printer paper cut into a square works too. Very thick paper makes the reverse folds harder.

Color. If your paper is colored on one side only, start with the colored side facing down. The colored side will end up on the outside of the bird.

Surface. Fold on a table or another hard, flat surface. It makes creases much sharper.

Time. Most beginners finish in about five to ten minutes. Your second bird will be faster.

Step-by-Step Instructions

Step 1: Fold a triangle

Lay the square on the table as a diamond, colored side down. Fold the bottom corner up to meet the top corner, line the corners up exactly, and crease firmly from the center outward.

Checkpoint: You have a triangle with the folded edge along the bottom and the point at the top. The colored side is on the outside.

Step 2: Fold it in half

Bring the left corner of the triangle over to meet the right corner. Line up the edges and crease firmly.

Checkpoint: You have a smaller triangle with one square corner and two sharp corners. One of its short edges is the fold you just made, where all the layers bend together.

Step 3: Turn it to the starting position

Rotate the small triangle so that:

  • the edge you folded in step 2 lies along the bottom,
  • the square corner is at the bottom left,
  • the loose flaps point up at the top left,
  • and the long, slanted edge runs from the top left down to the bottom right.

Checkpoint: The bottom right corner is a sharp point. That point will become the neck.

Step 4: Make the neck

Fold the bottom right point upward so it stands roughly upright. The fold line should start on the bottom edge about one-third of the way in from the right corner and angle up to the slanted edge. Crease hard, then unfold.

Now turn that crease into an inside reverse fold: open the two halves of the bird slightly, push the point up between them along the crease, and close the halves again. (See the section below if this is your first reverse fold.)

Checkpoint: A narrow point sticks up from the right side of the bird, tucked between the two halves rather than folded over the outside.

Step 5: Make the head

About a third of the way down from the tip of the neck, fold the tip forward (to the right) and crease. Unfold, then inside reverse fold it the same way you made the neck.

Checkpoint: The top of the neck bends forward into a small head, and the tip points ahead like a beak.

Step 6: Shape the wings

Take the front flap at the top left. Fold it down toward you along a line about halfway up, roughly parallel to the bottom edge. Fold only the wing, not the neck. Crease it, then let it open back up partway so it sticks out to the side.

Turn the bird around and do the same with the back flap.

Checkpoint: Looking at the bird from the front, the two wings form a shallow V.

Step 7: Finish the details

Draw an eye on each side of the head with a marker. If you’d like a neater tail, fold the square corner at the bottom left inside the body with a small reverse fold. Adjust the wings and neck until the bird sits the way you like.

How to Do the Inside Reverse Fold

The inside reverse fold is the key move in this bird and in most origami animals. It changes the direction of a point by tucking it between its own layers. Here’s the method in more detail:

  1. Pre-crease. Fold the point the way you want it to end up, as a normal fold over the outside. Crease it hard, then fold it back the other way along the same line and crease again. This makes the paper flexible along that line.
  2. Unfold. Return the point to where it started.
  3. Open the layers. Gently separate the two halves of the model near the point.
  4. Push the point through. Press on the spine of the point (the folded edge) so it pops inward and swings between the layers along your crease.
  5. Close and flatten. Bring the halves back together and press flat.

If the paper resists, the pre-crease probably isn’t sharp enough. A toothpick can help guide small points into place.

Common Mistakes and Fixes

The bird is uneven. The first fold probably wasn’t exactly corner to corner. Small errors at the start carry through every step. Starting over with a fresh sheet is often quicker than trying to correct it.

The neck folded over the outside instead of between the layers. That’s a regular fold rather than a reverse fold. Unfold it, open the halves and push the point between them using the same crease.

The neck is too short or too long. Move the neck fold line. Starting the fold farther from the corner makes a longer neck; starting it closer makes a shorter one.

The head crumpled. The paper near the tip is thick with layers. Pre-crease firmly in both directions, and make the head fold a little lower on the neck where there’s more room to work.

The wings won’t stay out. Crease the wing folds harder, then open them. Slightly thinner paper also holds its shape better.

Ways to Change It Up

  • Make a peace dove. Fold the same bird in white paper and add a small green leaf as an olive branch. Our guide to origami peace cranes and doves explains the meaning behind both birds.
  • Try different colors. Bright paper makes a cheerful songbird; gray paper with two dark bars drawn on each wing suggests a pigeon.
  • Change the pose. Raise the wings higher for a bird about to take off, or fold them down flatter for a resting bird.
  • Make a flock. Fold several in different sizes and string them together as a garland or mobile.

Next Birds to Try

Once this bird feels easy, the origami quail uses the same folded triangle turned the other way up, so it’s a natural next step. The easy origami penguin is another beginner model that shows off two-tone paper. When you’re ready for the bird base, try the origami flapping bird, whose wings move when you pull its tail.

For an overview of paper, folds and a full progression of models, see our beginner’s guide to origami birds.

The complete guide to origami birds

Origami Birds Step by Step: Easy Models for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →