Origami Birds

How to Fold an Origami Flamingo

Fold an origami flamingo from a bird base, with a long curved neck, a bent beak and a single leg, plus practical ways to help your paper flamingo stand.

On this page
  1. Before You Start
  2. Part 1: Fold a Bird Base
  3. Part 2: Narrow the Points Twice
  4. Part 3: Raise and Shape the Neck
  5. Part 4: Form the Head and Beak
  6. Part 5: Shape the Body and Leg
  7. Getting Your Flamingo to Stand
  8. Troubleshooting
  9. More Birds to Fold

Before You Start

How hard is it?

This flamingo is an intermediate model. It starts from the bird base, the same base used for the traditional crane, then narrows the lower points twice and uses several reverse folds in a row to shape the neck and head. If you’ve folded a crane or an origami flapping bird, you’ll already know the first half.

Paper

  • Size: Use at least a 20 cm (8 in) square if you can. The double narrowing builds up a lot of layers, and larger paper makes the neck folds far easier. A 15 cm (6 in) sheet works but is fiddly.
  • Thickness: Thin paper is best. Thick paper makes the neck stiff and the reverse folds bulky.
  • Color: Pink, of course, or coral or salmon. A darker marker can add the black tip on the beak.

Tools

  • A hard, flat surface
  • A toothpick for guiding reverse folds in narrow points

Part 1: Fold a Bird Base

  1. Diagonal creases. Colored side up, fold the square in half diagonally both ways, unfolding after each.
  2. Edge creases. Turn the paper over. Fold it in half edge to edge both ways, unfolding after each.
  3. Square base. Hold the paper as a diamond and bring the top, left and right corners down to the bottom corner along the creases. Flatten into a small square with the open end pointing toward you.
  4. Kite folds. Fold the lower left and right edges of the top layer in to the center crease.
  5. Top fold. Fold the top triangle down over the kite flaps, crease firmly, then unfold steps 4 and 5.
  6. Petal fold. Lift the bottom corner of the top layer up along the horizontal crease, letting the sides fold in along the kite creases. Flatten into a long diamond.
  7. Repeat. Turn over and repeat steps 4 to 6.

You now have a bird base: two wide flaps at the top and two narrow points at the bottom. The wide flaps will become the body and wings. One bottom point will become the neck and the other the leg.

Part 2: Narrow the Points Twice

  1. First narrowing. Fold the lower edges of the top layer in to the center crease. Turn over and repeat. This matches the narrowing step of a crane.
  2. Second narrowing. Fold the new lower edges in to the center again on both sides. Both bottom points are now long and very thin, which is what gives the flamingo its slender neck and leg.

Crease each narrowing fold firmly. The layers get thick here, so press along the full length of each fold.

Part 3: Raise and Shape the Neck

  1. Raise the neck. Inside reverse fold one bottom point upward so it rises between the wide flaps and stands nearly upright. Make this fold close to the body; flamingos have long necks, so you want as much length as possible above it.
  2. Add a curve (optional). For the classic S-shaped neck, make a crimp partway up: two reverse folds close together that push a section of the neck back and then up again. Pre-crease both folds before forming the crimp.

Part 4: Form the Head and Beak

  1. Bend the head. Near the top of the neck, inside reverse fold the point forward and down so the head hangs over in front of the neck.
  2. Bend the beak. Flamingo beaks have a distinctive downward bend. Make a small inside reverse fold near the tip so the end of the beak angles down.
  3. Color the tip. If you like, darken the end of the beak with a marker.

Each of these folds goes through many layers. Use a toothpick to open the layers, and pre-crease in both directions.

Part 5: Shape the Body and Leg

  1. Leave the leg down. The other narrow bottom point already points downward. That’s the flamingo’s leg. Leave it pointing down from the body, slightly angled if you like.
  2. Add a knee (optional). A small crimp partway down the leg can suggest the backward-bending joint that flamingos are known for.
  3. Fold the wings down. Fold the two wide flaps down so they lie along the sides of the body, angled toward the back, away from the neck. Together they form the rounded body.
  4. Shape. Gently curve the wings around the body, and adjust the neck and head so the bird looks balanced.

Getting Your Flamingo to Stand

A paper flamingo on one thin leg rarely balances on its own, so plan on giving it some help:

  • Use a base. Push the leg into a small slit in a piece of foam, cork or folded card, or fix it to a small base with a dab of glue.
  • Lean it. Stand the flamingo against a wall, a vase or another object.
  • Hang it. Thread a fine line through the top of the body and hang it as an ornament.
  • Mount it flat. Press the model flatter and glue it to a card or a framed background.

Troubleshooting

The neck won’t stay upright. The reverse fold at the base of the neck may be too far from the body. Move it closer and crease it firmly.

The head and beak folds won’t go through. There are many layers by this stage. Use a larger sheet, pre-crease carefully and use a toothpick to guide the point.

The neck and leg are too thick. Check that both narrowing steps reached the center crease exactly. Thinner paper also helps.

The body looks flat. Curve the wings gently and open the body slightly from underneath.

The model is lopsided. Uneven petal folds in the bird base are the usual cause. Careful alignment there makes the rest much easier.

More Birds to Fold

The origami hummingbird uses the same narrowing ideas to create a long, thin beak. For the classic model that both are built on, see our guide to origami peace cranes and doves. And for easier projects and a suggested order to learn them in, visit our beginner’s guide to origami birds.

The complete guide to origami birds

Origami Birds Step by Step: Easy Models for Beginners
Read the guide

Keep exploring

Guides from other topics

All topics →