What You Need
- One square of paper, about 15 cm (6 in). For a classic look, use paper that’s black or dark blue on one side and white on the other. The white side becomes the penguin’s belly.
- A hard, flat surface for crisp folds.
- A marker (optional) for eyes, or orange paper scraps for a beak and feet.
This penguin takes most beginners around five to ten minutes. It uses two inside reverse folds, which are explained below if you haven’t done them before.
Step-by-Step Instructions
Step 1: Crease the center
Place the paper as a diamond with the dark side facing up. Fold it in half from left to right, crease and unfold. You now have a vertical crease running from the top corner to the bottom corner.
Step 2: Fold in the left corner
Fold the left corner in toward the center crease, but stop short of it. The fold line should be vertical, parallel to the center crease. For a 15 cm square, aim for the tip of the corner to land roughly 2 cm (just under an inch) away from the center crease. A white triangle now shows on the left side.
Step 3: Fold in the right corner
Repeat with the right corner, so it mirrors the left. Try to make both sides match; they control how even the belly looks.
How much white shows depends on how far you fold the corners in. Folding them farther in gives a wider white belly. Folding them less gives a slimmer one.
Step 4: Fold the penguin in half
Fold the model in half along the center crease, folding backward, so the dark side ends up on the outside and the white triangles stay visible on both outer faces.
Turn the model so the center crease, now a single folded edge, is on the left. That’s the penguin’s back. The edge on the right, where the two white flaps meet, is its front. The top and bottom points both sit on the back edge.
Step 5: Make the head
Fold the top point forward and down so it points toward the front of the penguin, with the fold line starting on the back edge about a quarter of the way down from the top. Crease firmly and unfold.
Now inside reverse fold the top point along that crease: open the two halves slightly, push the top point down between them so it flips forward, and close the halves again. The tip that sticks out at the front is the beak.
Step 6: Make the base
Fold the bottom point up into the body along a roughly horizontal line, about 1 to 2 cm (half an inch or so) above the tip. Crease, unfold and inside reverse fold it so the point tucks up between the layers. This flattens the bottom so the penguin can stand.
Step 7: Shape and finish
Gently open the front edges a little so the white belly shows from the front. Draw eyes on each side of the head, or add small orange paper triangles for a beak and feet.
Getting Your Penguin to Stand
A penguin that tips over usually has an uneven or rounded base. Try these fixes:
- Square up the base fold. Make sure the bottom reverse fold in step 6 is level from front to back. If it slants, the penguin will lean.
- Open the body slightly. Spreading the two halves a little gives the penguin a wider footprint.
- Fold a larger base. Reverse folding more of the bottom point makes a broader, steadier base.
- Adjust the head. A very large head can make the model top-heavy. Fold the head a little smaller.
Variations to Try
- A penguin family. Fold one from a 15 cm square, one from a 10 cm square and a chick from a 7.5 cm square, then stand them in a row.
- Different species. Dark blue paper suggests a little blue penguin. A small dab of yellow or orange marker near the head hints at the markings of species like the king or emperor penguin.
- Holiday decorations. Add a tiny paper scarf or hat, or thread a loop through the back for a hanging ornament.
- Place cards. Write a name on the white belly and stand the penguins on a table.
Troubleshooting
The belly is uneven. The left and right corners weren’t folded the same distance. Measure from the center crease, or fold one side and use it as a guide for the other.
The head crumples. Pre-crease the head fold firmly in both directions before reversing it. Making the fold a little lower on the back gives you more paper to work with.
No white shows from the front. The corners may be folded in too far, so the front edges are dark. Fold them less in step 2 and 3, or open the front of the body slightly at the end.
The paper is the wrong way round. If the outside is white and the belly is dark, the paper started with the white side up. Start again with the dark side facing up.
More Birds to Fold
If you enjoyed this penguin, the easy origami bird step-by-step guide is another quick beginner model. For a small perched bird with a long tail, try the origami parakeet. And for an overview of paper, folds and a full progression of models, see our beginner’s guide to origami birds.