Before You Start
How hard is it?
This hummingbird is an intermediate model. It starts from the bird base, the same base used for the traditional crane, and then narrows the points further to get a long, thin beak. If you’ve folded a crane or an origami flapping bird before, you’ll recognize most of the early steps.
If the bird base is new to you, fold it once or twice on scrap paper before using your good sheet.
Paper
- Size: A 15 cm (6 in) square works, but 20 cm (8 in) or larger is easier, because the narrowing steps stack up layers in a small space.
- Thickness: Thin paper is important. Standard origami paper is fine; thicker paper makes the beak bulky and hard to fold.
- Color: Green, turquoise or red papers suit a hummingbird. Paper colored on both sides looks neater, since the inside of the wings can show.
Tools
- A hard, flat surface
- A toothpick or similar tool for opening tight layers during reverse folds
Part 1: Fold a Bird Base
- Diagonal creases. Colored side up, fold the square in half diagonally both ways, unfolding after each.
- Edge creases. Turn the paper over. Fold it in half edge to edge both ways, unfolding after each.
- Square base. Hold the paper as a diamond and bring the top, left and right corners down to the bottom corner along the creases. Flatten into a small square with the open end pointing toward you.
- Kite folds. Fold the lower left and right edges of the top layer in to the center crease.
- Top fold. Fold the top triangle down over the kite flaps, crease firmly and unfold steps 4 and 5.
- Petal fold. Lift the bottom corner of the top layer up along the horizontal crease, letting the sides fold in along the kite creases. Flatten into a long diamond.
- Repeat. Turn the model over and repeat steps 4 to 6.
You now have a bird base: a long diamond with two wide flaps at the top and two narrow points at the bottom.
Part 2: Narrow the Points
- First narrowing. Fold the lower edges of the top layer in to the center crease. Turn the model over and repeat. This is the same step that narrows a crane’s neck and tail.
- Second narrowing (beak point only). On the lower point you plan to use for the head and beak, fold the edges in to the center once more on both sides. This makes it noticeably thinner than the tail point. It’s fiddly, so take your time and crease firmly.
Part 3: Shape the Head and Beak
- Raise the neck. Inside reverse fold the thinner bottom point upward so it rises between the wide flaps and points up and slightly forward. Hummingbirds have short necks, so make this fold close to the body.
- Form the head. A short distance above the body, inside reverse fold the point forward so it angles out nearly horizontally. The bend becomes the head, and the long remaining point becomes the beak.
- Refine the beak. If the beak looks too wide, fold its edges in slightly or narrow it once more near the tip. A toothpick helps keep the layers in place.
Aim for a small head and a long beak. If too much paper ends up in the head, make the head fold closer to the body next time.
Part 4: Shape the Tail
- Tail angle. Inside reverse fold the other bottom point so it points back and slightly down from the body. Hummingbird tails are fairly short, so you can shorten it by reverse folding the tip inside, or leave it longer for a more stylized look.
- Optional spread. Gently open the end of the tail a little to suggest a fanned tail.
Part 5: Raise the Wings
At this point the two wide flaps still point straight up.
- Angle the wings. Fold each wide flap outward and down only part of the way, so the wings sit raised in a V above the body rather than folded flat like a crane’s.
- Shape. Curve each wing slightly by running it over your finger. You can also make a few small pleats along the back edge of each wing to suggest feathers.
- Balance. Adjust the head, tail and wings until the bird looks balanced and alert.
Displaying Your Hummingbird
- Beside a flower. Glue the hummingbird to a thin wire, bamboo skewer or florist’s stem and position it so its beak points into a paper or fabric flower.
- Hanging. Thread a fine line through the top of the body and hang it near a window, where it will turn gently.
- On a card. Fold the wings flatter and mount it on the front of a greeting card.
- In a group. Fold several in different colors and sizes for a mobile.
Troubleshooting
The beak is thick and stubby. Use thinner or larger paper, crease the second narrowing very firmly, and make the head fold closer to the body so more length goes to the beak.
The reverse folds won’t go through. There are many layers at this point. Pre-crease in both directions, open the layers wider and use a toothpick to guide the point.
The wings look like a crane’s. You’ve likely folded them all the way down. Lift them back up partway for the raised hummingbird pose.
The model is uneven. Check the bird base: if the petal folds weren’t symmetrical, everything after them will be slightly off. Refolding with careful alignment usually fixes it.
The paper tears near the beak. Repeated narrowing puts stress on the paper. Try a slightly larger sheet so each fold has more room.
What to Fold Next
The origami flamingo uses the same narrowing ideas to make a long, curved neck. For background on the crane that this hummingbird builds on, see our guide to origami peace cranes and doves. And for easier models and a full progression, visit our beginner’s guide to origami birds.