You can fold an origami pumpkin in two main ways. A flat pumpkin takes about five minutes and is ideal for cards, garlands and window decorations. A 3D pumpkin is folded from the classic waterbomb base, then inflated and gently squashed into a round pumpkin shape. Both use one square of orange paper, and both are below.
Choosing paper
- Size: a 15 cm (6 in) square suits both models. Smaller squares, around 7.5 cm (3 in), make good garland pumpkins but are fiddly for the 3D version.
- Color: orange on at least one side. Orange-and-green two-tone paper is handy because it can give you a green stem without a marker.
- Weight: standard origami paper (kami) is best. Thick paper is hard to inflate for the 3D pumpkin.
A quick note on bases, since instructions often mix them up. A square base (also called a preliminary base) collapses into a small square. A waterbomb base collapses into a triangle. They use the same creases folded in opposite directions. The 3D pumpkin below uses the waterbomb base.
Flat origami pumpkin, step by step
- Crease the diagonals. With the orange side up, fold the square in half along each diagonal and unfold. Turn it so it sits as a diamond.
- Turn over. Now the white (or second-color) side faces up.
- Fold the top and bottom points to the center. Fold the bottom point up to the center, then fold the top point down to the center. You now have a wide hexagon with flat top and bottom edges.
- Turn back over. The front is plain orange.
- Blunt the sides. Fold the left and right points in by about 1–2 cm (½–¾ in) so the pumpkin is wide but not pointed.
- Round the corners. Fold each of the four remaining corners slightly behind. These are the places where the flat top and bottom edges meet the slanted sides. Small folds round the outline into a pumpkin shape.
Making the stem
There are a few easy ways to add a stem:
- Folded stem: in step 3, fold the top point down only partway, then fold its tip back up so a small point sticks out above the top edge. Depending on which way your paper faces, this may show orange or the second color. If it shows orange, color it green or brown with a marker.
- Paper stem: cut a small rectangle of green or brown paper, roll or fold it narrow, and glue it behind the top center.
- Leaf: add a small green leaf shape next to the stem for extra detail.
Rounding the shape
The more small corner folds you make, the rounder the pumpkin looks. For a squat pumpkin, fold the side points in more. For a tall pumpkin, fold them in less and fold the top and bottom points slightly past the center in step 3.
3D origami pumpkin from a waterbomb base
This is a pumpkin variation on the traditional origami waterbomb, a folded paper balloon.
Folding the waterbomb base
- Crease the diagonals. Start with the white (or second-color) side up. Fold the square in half along both diagonals, unfolding each time.
- Crease the middles. Turn it over so the orange side faces up. Fold it in half side to side and top to bottom, unfolding each time.
- Collapse. Keep the orange side up. Push the middles of two opposite edges in toward each other. The center rises and the paper collapses along the creases into a triangle, with two flaps on each side and orange on the outside. This is the waterbomb base. Place it with the point at the top.
Folding and inflating
- Fold the bottom corners up. On the front layer, fold the left and right bottom corners up to the top point. The front is now a diamond. Turn over and repeat.
- Fold the sides to the center. On the front layer, fold the left and right corners of the diamond in to meet at the vertical center line. Turn over and repeat.
- Tuck the top flaps. At the top are small loose flaps. Fold each one down over the triangles you just made, then tuck it into the pocket of that triangle. Turn over and repeat.
- Inflate it. Find the small hole at the bottom point of the model. Hold the model loosely and blow gently into the hole. It puffs up into a cube-like balloon. If it doesn’t inflate fully, gently pull the side flaps apart while blowing.
Shaping it into a pumpkin
- Squash it gently. Turn the balloon so the hole is at the top. Press down very lightly on the top and bottom so the balloon becomes a wider, flatter shape, like a real pumpkin.
- Add ribs. Gently pinch soft vertical creases around the sides, from top to bottom, to suggest the pumpkin’s segments.
- Add a stem. Roll a small strip of green or brown paper into a tight tube and push one end into the hole at the top. Add a dab of glue if it won’t stay.
For a more detailed 3D pumpkin with sharp segments, several origami designers publish more advanced models. Jo Nakashima’s origami pumpkin video, for example, is widely viewed. Those models take more steps but give a very realistic result.
Turning it into a jack-o’-lantern
- Draw a face with a black marker. Triangle eyes and a zigzag mouth are classic.
- On the flat pumpkin, glue on black paper cutouts for a crisp face.
- On the 3D pumpkin, draw the face after inflating and shaping. Drawing it before means the face stretches and moves as the model puffs up.
- Never put a candle or other flame inside or near a paper pumpkin. If you want it to glow, place it near a battery-powered LED tea light and keep the paper from resting on the light.
Troubleshooting
- The waterbomb won’t collapse. Make sure the diagonals and the side-to-side folds were creased from opposite sides of the paper, as in steps 1–2, then collapse again. Creasing them all from the same side is the usual cause.
- The white side ends up outside. Push the paper the other way in step 3 so the center rises toward you on the orange side.
- The 3D pumpkin tears when inflating. Blow more gently, or use slightly thicker paper. Very thin tissue-like paper tears easily.
- The flat pumpkin looks like a diamond. Fold the side points in farther and round all four corners.
- The stem shows the wrong color. Color it with a marker or use a separate stem piece.
Display ideas
String flat pumpkins on a garland, glue them onto cards, or scatter 3D pumpkins down the middle of a table. They pair naturally with a swarm of origami bats for Halloween. For hanging tips, such as threading through the top without tearing the paper, see our guide to origami Christmas decorations. The same methods work in October.