Quick answer
The simplest way to make a dinosaur is to fold a long-necked origami dinosaur from one square of paper. Fold the square into a fish base, fold it in half so the two small flaps hang down as legs, then use inside reverse folds to lift the neck and head at one end and angle the tail at the other. It takes about 15 minutes the first time.
If you’d rather not fold, a cardboard tube dinosaur is a quick craft: a flat cardboard dinosaur slotted into a short tube that acts as legs. Both are below.
What you need
- One square of paper. A 15 cm (6 in) square is easiest to start with. Green, brown or patterned paper all suit a dinosaur. Standard origami paper is better than printer paper here, because the base has several layers.
- A marker for eyes and details.
- Optional: scissors and a small piece of extra paper for spikes or plates.
Two folds to know first
Fish base. This is a traditional base shaped like a diamond with two small triangular flaps sticking out from the middle. It’s named after the simple origami fish it’s used for. You’ll fold it in steps 1 to 4 below.
Inside reverse fold. This changes the direction of a point, such as turning a neck upward. With the model folded in half, crease the point where you want it to bend, unfold, then open the layers slightly and push the point inside, between the two halves, along that crease. Flatten it again. The point now angles in a new direction, and the outside stays neat.
If you’ve never done a reverse fold, practice once on a scrap triangle. It’s the key skill in this model.
Simple origami long-necked dinosaur, step by step
- Crease a diagonal. Place the square as a diamond, white side up if your paper is one-sided. Fold it in half from left corner to right corner and unfold, leaving a vertical crease.
- Make a kite at the top. Fold the two upper edges in so they line up with the vertical crease, forming a kite shape at the top. Crease well, then unfold.
- Make a kite at the bottom. Fold the two lower edges to the vertical crease in the same way. Crease, then unfold.
- Collapse into the fish base. Refold the top kite folds. Then refold the bottom kite folds. Where the top and bottom folds meet near the middle on each side, the extra paper pinches up into a small triangular flap. Flatten each flap so it points outward to the side. You now have a diamond with a small flap on the left and right. This is the fish base.
- Fold in half. Fold the model in half along the long vertical center line, folding the left half behind the right so the two small flaps stay on the outside. Both flaps now point the same way.
- Turn it into a dinosaur shape. Rotate the model so the long center fold runs horizontally along the top and the two flaps hang down. Those flaps are the legs.
- Lift the neck. Choose one end to be the front. Inside reverse fold that end so it points up at a steep angle, forming the neck.
- Make the head. Near the tip of the neck, inside reverse fold a short section so it points forward. This is the head.
- Shape the tail. At the other end, make a small inside reverse fold so the tail angles slightly downward or out behind.
- Adjust the legs. If the legs are wide, fold each one in half lengthwise to make it narrower, or angle them slightly forward so the model balances.
Add two eyes with a marker, and your sauropod-style dinosaur is done.
Getting it to stand
- Spread the legs slightly so the front and back flaps form a small tripod with the tail, or let the tail tip touch the table as a third support.
- Shift the neck angle. A very long, forward-leaning neck tips the model over. Raise it a little until it balances.
- Use crisper paper. Soft or very thin paper sags. Standard kami or slightly heavier origami paper stands better.
Easy variations
- Stegosaurus look: draw a row of plates along the back, or glue on small folded paper triangles.
- Shorter neck: make the neck reverse fold lower and shorter for a stockier dinosaur.
- Head-only T. rex: for very young children, fold a triangle from a square and draw a big toothy mouth along the long edge. It’s barely origami, but it’s a fun dinosaur in two folds.
- Herd: fold several in different sizes and colors to make a family.
No-fold option: cardboard tube dinosaur
This is a good craft for preschoolers, with an adult doing the cutting.
- Draw the body. Sketch a simple dinosaur side view, without legs, on thin cardboard such as a cereal box. Cut it out.
- Prepare the tube. Cut a toilet paper or kitchen roll tube down to a few inches tall.
- Make legs. Cut a U-shaped arch out of the bottom of the tube on two opposite sides, so the remaining sections look like four stubby legs.
- Cut slots. Cut two small notches at the top of the tube on opposite sides, lined up front to back.
- Assemble. Slide the cardboard dinosaur body into the slots so it stands on the tube. Paint, color or add stickers.
Using paper dinosaurs as decorations and gifts
Dinosaurs aren’t a traditional holiday symbol, but they’re a favorite with children, and a folded dino makes a playful ornament or gift topper. Thread a loop through the middle of the back to hang one on a tree. You can also tape one to a wrapped present for a young dinosaur fan. Our guide to origami Christmas decorations covers hanging methods that won’t tear the paper.
If you enjoyed this, an easy origami reindeer is another beginner-friendly animal, and the origami bat is a simple model for Halloween.