Quick answer
The most popular way to make a paper star is the puffy lucky star. Tie a loose knot near one end of a long, narrow strip of paper and flatten it into a pentagon. Wrap the rest of the strip around the pentagon until it runs out, tuck in the end, and then pinch the five sides inward so the star puffs up. A strip about 1 cm (⅜–½ in) wide and 20–28 cm (8–11 in) long makes a fingertip-sized star.
You can also fold a 3D star from a square, cut a five-pointed star from folded paper with one snip, or fold a two-piece ninja star. All four methods are below.
Method 1: Puffy lucky star from a strip
Lucky stars are small, quick and addictive. People fold them by the hundred to fill jars or string into garlands.
Strip size
- Width: about 1–1.3 cm (⅜–½ in).
- Length: roughly 20–28 cm (8–11 in). Longer strips make a sturdier star with more wraps. The width sets the star’s size.
- Paper: thin paper works best. Precut star strips are sold at stationery shops, but strips cut from magazines, wrapping paper, old calendars or origami paper all work.
Steps
- Tie a loose knot. Near one end, loop the strip around and pass the short end through, as if tying a knot in a ribbon.
- Flatten it into a pentagon. Gently pull until the knot lies flat as a neat five-sided shape. Don’t pull too hard, or it tears or distorts. Leave a short tail of about 1–1.5 cm (½ in).
- Tuck the short tail. Fold the short tail over the pentagon and tuck it into the layers, or trim it so it doesn’t stick out.
- Wrap the long strip. Fold the long strip flat along the edge of the pentagon, then along the next edge, and keep going around. Each wrap follows the pentagon’s edge, so the shape stays the same while it gets thicker.
- Tuck the end. When the remaining strip is too short for another full wrap, trim it if needed and tuck the end under the layer on the nearest side.
- Puff it. Hold the pentagon by two opposite points and press the middle of one flat side inward with a fingernail. The side caves in and the corners pop out as points. Repeat on all five sides.
If your star won’t puff
- The knot was pulled too tight. A tight, creased knot makes a flat star. Keep the first pentagon slightly loose.
- The wraps were creased hard. Fold the wraps neatly but don’t press them flat with your nail.
- The paper is too thick. Cardstock and heavy paper resist puffing. Use thin paper.
- The points are uneven. Press each side by the same amount, working around the star once, then go around again to even it out.
Method 2: 3D paper star from a square
This makes a raised four-pointed star that looks great on a card or, with two glued back to back, as an eight-pointed hanging ornament.
- Start with a square of thin cardstock or sturdy paper. 15 cm (6 in) is a good size.
- Fold it in half along both diagonals, unfolding each time. Turn it over and fold it in half side to side and top to bottom, unfolding each time. The diagonals should rise toward you as ridges and the side-to-side folds should dip away as valleys.
- From the middle of each edge, cut along the valley crease about a third of the way toward the center. Don’t cut to the center.
- At each cut, overlap the two flaps on either side, sliding one behind the other. The diagonals pop up into four ridged points. Glue each overlap.
- For a hanging ornament, make two and glue them back to back with a thread loop sandwiched between them.
Method 3: Five-pointed star with one cut
A flat five-pointed star can be made by folding paper so the center point is divided into ten narrow, equal wedges. Then you make one straight cut across the folded bundle. When you unfold it, the paper opens into a star. The angle of the cut controls the look. A steep cut gives thin, sharp points, and a shallow cut gives chunky points.
The fiddly part is getting the wedges equal. Many people use a printed folding template the first time, or fold a tested pattern of landmark creases. Once you’ve made one, you can make paper chains of stars by folding a long strip accordion-style before cutting. Children should use safety scissors, and an adult should check the folding before the cut.
Method 4: Origami ninja star step by step
The ninja star, or shuriken, is made from two squares of the same size. Two colors look best. Each square becomes a unit, and the units lock together without glue.
- Make two long strips. Fold each square in half and unfold. Fold the two outer edges to the center crease, then fold in half along the center again. Each square is now a long, narrow strip four layers thick.
- Find the middle. Fold each strip in half crosswise and unfold.
- Make the Z shape. On the first strip, fold the left half down and the right half up, each at a right angle at the middle. You get a stepped or Z-like shape.
- Make the second unit as a mirror image. On the second strip, fold the halves the opposite way. This is the step people most often get wrong. If both units match exactly, they won’t lock.
- Fold the ends into points. On each unit, fold each end diagonally into a triangle so the strip ends become pointed tips. The triangles on one unit should point in opposite directions.
- Lock them together. Turn one unit over and lay it crosswise on top of the other so the centers line up. Fold each point of the bottom unit over and tuck it into the pocket on the top unit. Turn over and tuck the remaining points the same way.
Ninja stars are toys for display and gentle play. Remind children never to throw them at people or pets.
Which paper star should you make?
| You want… | Best method |
|---|---|
| A jar full of stars or a tiny garland | Lucky stars |
| A raised card decoration or ornament | 3D star from a square |
| A flat window or wall star | One-cut star |
| A fun folding toy for kids | Ninja star |
For bigger, more traditional Christmas stars, such as woven Froebel stars, spiky Moravian-style stars and pop-up stars that fold flat, see our guide to origami Christmas stars. For ways to hang stars with other folded ornaments, see the origami Christmas decorations guide.
What do origami paper stars mean?
Lucky stars are especially popular in East Asia. A jar of folded stars is a common gift between friends and couples, and is often given as a token of good luck or affection. Some people write a wish or a message on the strip before folding it. A widely shared belief, similar to the story of folding 1,000 paper cranes, is that folding a large number of stars brings luck or a wish. Treat that as a folk custom rather than a fixed tradition, since the details vary from person to person.
What is the easiest origami to start with?
There’s no official “easiest” model, but very simple folds such as a paper cup, a dog face or a basic tulip take only a few steps. The lucky star is also a good first project because it uses one repeated motion and needs no measuring. Once you’re comfortable, a simple reindeer face is a natural next step for the holidays.