Origami Crafts

How to Fold Origami Lucky Stars for a Wish Jar

How to make origami lucky stars from paper strips: strip sizes, knotting, wrapping and puffing, plus troubleshooting and tips for filling a wish jar.

On this page
  1. What you need
  2. Cutting your own strips
  3. How to make origami lucky stars, step by step
  4. Troubleshooting
  5. Filling a wish jar
  6. Other ways to use lucky stars

Origami lucky stars are small, puffy five-pointed stars folded from a single strip of paper. They’re quick to make once you’ve got the knack, and a jar full of them makes a popular handmade gift. Many people write a wish, a memory or a short message on each strip before folding, which is where the “wish jar” idea comes from.

What you need

  • Paper strips. Lucky star paper is sold in pre-cut packs, often in bright colors and patterns. You can also cut your own (see below).
  • Scissors or a paper trimmer, if cutting strips.
  • A fine-tip pen, if you’re writing wishes.
  • A clear jar or bottle to fill.

Thin paper works best. Standard origami paper, printer paper, wrapping paper and magazine pages all make good stars. Very thick paper is hard to puff.

Cutting your own strips

A good starting size is a strip roughly 1 to 1.5 cm (about 0.4 to 0.6 in) wide and 25 to 30 cm (about 10 to 12 in) long. What matters most is the ratio: a strip about 20 to 25 times longer than it is wide gives a well-proportioned star.

  • From a sheet of Letter or A4 paper, cut strips along the long side to get the right length.
  • From a 15 cm (6 in) origami square, strips will be short. Tape or glue two together end to end, or make tiny stars with narrower strips.
  • Wider strips make bigger stars. Narrower strips make smaller ones. Keep the length in proportion.

A paper trimmer makes it much easier to cut many strips of an even width.

How to make origami lucky stars, step by step

Step 1: Write your wish (optional)

If you’re filling a wish jar, write your message along the strip first, on the side that will end up inside. Keep it short, and write in the middle portion of the strip, since the ends get folded into the knot and tucked away.

Step 2: Tie a loose knot

Near one end of the strip, make a loop and pass the short end through it, as if you were tying a simple overhand knot in a ribbon. Leave a short tail of about 2 to 3 cm (1 in) on one side.

Pull the knot gently. Don’t crease it yet.

Step 3: Flatten into a pentagon

Slowly tighten the knot while easing it flat. As it closes, it naturally forms a flat pentagon. Press it flat and crease the edges. Neat, even edges here make a neater star.

Step 4: Tuck the short tail

Fold the short tail over along the edge of the pentagon and tuck it into the pocket behind it. Trim it first if it’s too long to tuck neatly.

Step 5: Wrap the strip around

Take the long end and fold it over the edge of the pentagon so it lies flat against the next side. Keep going: each wrap follows the pentagon’s edges naturally, one side at a time.

  • Keep the strip flat and the tension even: firm, but not tight.
  • Line each wrap up with the pentagon’s edges so it stays symmetrical.

Step 6: Tuck the end

When there’s only a short bit of strip left, fold it over and tuck it into the nearest pocket formed by the last wrap. Trim any excess first so it fits.

You should now have a flat, layered pentagon.

Step 7: Puff the star

Hold the pentagon by two corners. Use a fingernail to press gently into the middle of one flat side, pushing it inward. Turn it and repeat on all five sides. As each side dents in, the center puffs up and the five points form.

Go gently and work around the star more than once if needed. Pressing too hard in one place can crumple it.

Troubleshooting

  • The star won’t puff. It’s usually wrapped too tightly. Next time, wrap with slightly less tension. Thicker paper also makes puffing harder.
  • The star is lopsided. The pentagon wasn’t even, or the wraps drifted off its edges. Take extra care with step 3.
  • The tail won’t tuck. Trim it shorter, or slip it in at a slight angle.
  • There’s too little strip. Use a longer strip for the width, or a narrower strip for the length you have.
  • The star feels loose. Wrap a little more firmly, and make sure the final end is tucked deep into a pocket.

Filling a wish jar

  • Choose a jar with a clear wall and a lid or cork. Small bottles are good for a few dozen stars, and larger jars hold hundreds.
  • Pick a number. Some people fold a symbolic number, such as one per day of the year or one for each year of someone’s age. Others just fill the jar.
  • Plan colors. One color, a gradient, or layers of different colors all look good through glass.
  • Add messages. Write wishes, memories, reasons you love someone, or small encouragements on each strip.
  • Finish the jar with a ribbon, a tag or a small folded heart on the lid.

Because lucky stars are quick once you have the rhythm, many people fold them a few at a time over days or weeks.

Other ways to use lucky stars

For more ideas, browse our full list of crafts from origami paper.

The complete guide to origami crafts

Crafts from Origami Paper: Decor, Gifts and DIY Ideas
Read the guide

Keep exploring

Guides from other topics

All topics →