The short answer
The simplest homemade pop-up takes one sheet of paper, two cuts and a fold:
- Fold a sheet of paper or light card in half.
- From the folded edge, cut two parallel slits of the same length.
- Fold the strip between the slits back and forth along the line joining the slit ends, and crease it hard.
- Open the sheet partway and push the strip through to the inside, so it stands out as a block.
- Close the sheet and press to set the folds, then glue a picture or folded model to the front of the block.
That’s the basic step (or box) pop-up, and most homemade pop-ups are variations on it or one of a few other mechanisms. The rest of this guide explains those mechanisms and how to combine them.
What you need
You can make pop-ups from things found in most homes:
- printer paper or thin card (cereal box card works for covers)
- scissors, or a craft knife and cutting mat for adults
- a ruler and pencil
- a glue stick
- something for scoring folds: an empty ballpoint pen or the back of a butter knife
Scoring tip: for anything thicker than printer paper, run a scoring tool along the fold line against a ruler before folding. Folds will be crisper and less likely to crack.
The simplest pop-up, step by step
Here’s the step pop-up from the short answer with measurements, using a Letter or A4 sheet:
- Fold the sheet in half widthwise.
- On the folded edge, mark two slits 3 cm (about 1.25 in) long and 5 cm (2 in) apart.
- Cut both slits through both layers.
- Fold the strip between them back along the line joining the slit ends, crease, fold it forward, and crease again.
- Open the sheet to a right angle, push the strip through to the inside, and close it. When you open it again, a block stands up.
The block sticks out about as far as the slits are long and is about that tall. The gap between the slits sets its width. Longer slits make a bigger block, and a pair of slits that’s wide but short makes a low platform.
For more measured layouts, including a three-block skyline and a folded flower bouquet card, see our origami pop-up card templates.
Five pop-up mechanisms to know
Step (box) fold
The step fold described above is the workhorse. You can:
- put several side by side with different slit lengths to make a skyline or staircase
- cut a smaller pair of slits into an existing step to create a second, nested step
- glue a picture to the front face so it appears to stand in front of the background
V-fold
A V-fold is a separate folded piece glued across the center fold of the card or page, rather than cut from it.
- Fold a small rectangle of card in half.
- Fold a narrow glue tab outward along the bottom edge of each half.
- Glue one tab on each side of the center fold, so the piece’s own fold sits exactly on the page’s center fold. Keep both tabs at matching angles.
As the page opens, the piece rises into a V shape. V-folds are good for animals, trees, or mouths that open and close.
Floating layer
A floating layer is a flat panel held up off the page by two small folded supports, like a little table. Fold two narrow strips into short boxes or “Z” shapes and glue one at each end of the panel and to each side of the page. When the page opens, the panel lifts and floats above the background. It’s useful for clouds, signs or a second scene layer.
Pull tab
A pull tab makes something move when you slide a strip:
- Cut a slot in the page.
- Thread a strip of card through it from behind.
- Glue a picture to the strip’s front end, through the slot.
- Add a small “stopper” (a scrap of card glued across the strip) so it can’t be pulled out completely.
Pull it to make the picture slide across the page, a simple way to make a character walk or a sun rise.
Accordion spring
An accordion spring is a strip of paper folded back and forth like a fan or zigzag. Glue one end to the page and a picture to the other. When the card opens, the picture bounces forward on the spring. Two strips folded over each other at right angles (a “paper spring” or “jack-in-the-box fold”) make a bouncier spring.
The rule every pop-up must follow
A pop-up has to fold flat when it closes. Almost every homemade pop-up problem breaks this rule. Before any glue dries, close the page gently and check:
- Does any part stick out past the edges?
- Does anything tear, bend sharply or get crushed?
- Is anything glued in a spot that should stay free to move?
If something sticks out, shorten it, move it closer to the center fold, or trim it. Checking as you go saves a lot of remakes.
Making a homemade pop-up book or scene
A pop-up book is several pop-up pages glued back to back:
- Make each spread separately. Each page is a sheet folded in half with its own pop-ups.
- Glue the spreads back to back. Glue the outside of the right half of spread 1 to the outside of the left half of spread 2, and so on. Keep glue away from the backs of any cut pop-ups.
- Add a cover. Wrap a sheet of thicker card around the whole stack and glue it to the outer pages.
- Write the text around the pop-ups, or on small flaps that lift.
For a single standing scene, such as a diorama, use a step fold as a stage and layer pictures at different depths. A background on the back wall, a character on the step, and a floating layer above make a simple three-layer scene.
Common problems and fixes
- The pop-up doesn’t stand up. Re-crease the folds at the ends of the slits in both directions.
- It sticks out when closed. The slits are too long for the page, or a decoration is too big. Shorten or trim.
- The page tears at the slit ends. The paper may be too thin. Use slightly thicker paper, or reinforce the back with a small piece of tape.
- Thick card won’t fold neatly. Score the fold first.
- Glue stops the pop-up working. Glue spread onto a moving part. Use a glue stick and work carefully near cuts.
Pop-ups make a lovely base for other folded projects. Try mounting a small crane, star or heart on the front face, or tuck a few origami lucky stars into an envelope with the card. For more gift ideas, see our collection of crafts from origami paper.