The Easiest Dollar Bill Butterfly
The simplest way to make a dollar bill butterfly is to pleat the bill like a paper fan, pinch it in the middle and spread out the two sides as wings. Folding two small notches into the bill before you pleat splits each side into an upper and a lower wing, so the finished butterfly has four wings instead of looking like a bow.
This version takes about 10 minutes, needs no cutting or glue, and works with any U.S. bill. The finished butterfly is about 2 1/2 inches (6.5 cm) across.
If you haven’t folded money before, the beginner’s guide to dollar bill origami covers how to prepare a bill and practice the accordion pleat.
What You Need
- One crisp bill
- A pipe cleaner (chenille stem) or twist tie for the body
- A hard, flat surface
A pipe cleaner works best, because you can twist its ends into antennae. It holds the bill without damaging it and comes off easily when it’s time to spend the money.
Step 1: Make the Wing Notches
The notches are what split each wing in two.
- Lay the bill flat with its long side horizontal. The side facing down will be the outside of the wings.
- Fold the bill in half end to end so the two short edges meet. Crease firmly.
- Keep the bill folded. At the folded edge, fold the top corner down in a small triangle. Each side of the triangle should be about 1/2 inch (1.3 cm) long. Fold the bottom corner of the folded edge up the same way.
- Unfold the end-to-end fold only. Leave the small triangles folded.
You should now have a bill with a V-shaped notch in the middle of the top edge and another in the middle of the bottom edge. The little triangles are folded behind the notches.
Step 2: Pleat the Bill
Next, pleat the bill into a narrow stack with all the folds running parallel to the short edges.
- The center crease from Step 1 is already there. Fold each short edge to the center crease and unfold, so the bill is divided into quarters.
- Fold the left edge to the nearest quarter crease and unfold. Then fold the left edge to the quarter crease on the far side of the center and unfold. Repeat from the right edge. You now have eight equal sections.
- For neater wings, divide each section in half by eye, giving 16 sections about 3/8 inch (1 cm) wide. Eight sections also work, but the wings look chunkier.
- Re-fold the creases as an accordion, alternating valley and mountain folds from one end to the other. Keep the notch triangles tucked flat as you go.
- Squeeze the finished stack hard and run your fingers along it to sharpen every crease.
The pleated stack will be about 2 1/2 inches (6.5 cm) long, which is the short side of the bill. Both notches sit in the middle of the stack, one at each end.
Step 3: Pinch and Tie the Middle
- Find the middle of the stack’s length, halfway between the two notched ends.
- Pinch the stack tightly there.
- Wrap the pipe cleaner around the pinch once or twice and twist it snug behind, leaving two ends sticking up for antennae. If you’re using a twist tie, twist it snug and tuck its ends behind.
The pinch is the butterfly’s body. Each half of the stack becomes one side of the wings.
Step 4: Open the Wings
- Hold the body and gently spread the pleats on one side into a fan. Then spread the other side the same way.
- Look at each fan. The notch sits in the middle of its outer edge, so each fan should now look like two lobes: an upper wing and a lower wing.
- Spread each fan until it’s about a half circle, so its edges line up with the body.
- Turn the butterfly so the body runs up and down, and curl the pipe cleaner ends into antennae.
Tips for a Neater Butterfly
- Even pleats matter most. Making the creases by folding edges to existing creases keeps the pleats even, which gives you smooth, symmetrical wings.
- Tie at the exact middle. If the pinch is off center, one side of the wings will be bigger than the other.
- Deeper notches = more separated wings. Triangles about 1/2 inch (1.3 cm) on a side give a clear split. Slightly larger triangles make the split more dramatic.
- Use a new bill. Soft, worn bills don’t hold the fan shape well.
Variations
- Two-bill butterfly. Pleat one bill as above for the upper wings. Fold a second bill in half lengthwise before pleating it, so it makes smaller lower wings. Stack them with the smaller one below and tie them together in the middle.
- Bigger gift. Fold the butterfly from a $5, $20 or larger bill. Every U.S. denomination is the same size, so the steps don’t change.
- Pure-fold butterflies. Some money-folding books include butterflies that hold together with folds alone, without a tie. They’re harder, but they’re worth trying once you’re comfortable with the basics.
Troubleshooting
The wings won’t separate into upper and lower halves. The notches are probably too small or got flattened during pleating. Unfold, make the triangles a little bigger and pleat again.
The fans spring closed. The creases aren’t sharp enough. Squeeze the pleated stack hard before tying, and use a crisp bill.
One side is bigger than the other. The tie isn’t centered. Slide it toward the larger side before spreading the wings.
FAQ
How do you make a simple origami butterfly for beginners?
The easiest butterfly for beginners is an accordion butterfly like this one: pleat a piece of paper or a bill back and forth, pinch it in the middle and spread the two sides. It doesn’t need any precise origami bases. For square origami paper, a waterbomb-base butterfly is a common next step once you’re comfortable with basic folds.
How can I fold origami using a dollar bill?
Most dollar bill models start by folding the long bill into a strip or a set of pleats, rather than the diagonal folds used on square paper. Easy first projects include a dollar bill heart, a bow tie and a ring. The pleating you learn here is also the base of the three-bill money flower.