A Simple Wrapped Dollar Bill Ring
This dollar bill ring is made by folding the bill into a narrow band, wrapping it around your finger, and then coiling the leftover tail around the band to lock it in place. The coils make a small wrapped “knot” on top of the ring. It takes about five minutes, and because you size it on the actual finger, it fits.
You’ll often see a more advanced dollar ring with a square top that frames one of the bill’s large “1” numerals. That version takes more steps and some practice. The wrapped ring here is a good first ring, and it teaches the band-folding you’ll use in the bezel version later.
If you’re new to money folding, see the dollar bill origami basics for how to prepare a bill.
What You Need
- One crisp bill. A new bill holds the band shape much better than a soft one.
- A hard, flat surface.
- Optional: a marker, lip balm tube or dowel about the size of the finger, for shaping.
Step 1: Fold the Bill Into a Band
- Lay the bill flat with the long side horizontal.
- Fold it in half lengthwise, bringing the bottom edge up to the top edge. Crease and unfold.
- Fold the top and bottom long edges to the center crease.
- Fold the strip in half along the center so the raw edges are hidden inside. You now have a strip about 5/8 inch (1.6 cm) wide, and both long edges are clean folds.
- Fold the strip in half lengthwise once more. The band is now about 5/16 inch (8 mm) wide.
- Run your fingernail along the whole band to flatten it.
The band is about 6 inches (15 cm) long. A typical adult ring needs only about 2 to 2 1/2 inches (5 to 6.5 cm) of it to go around a finger, so there’s plenty left for locking.
Step 2: Size the Ring on Your Finger
- Hold one end of the band on top of the finger, with about 1/2 inch (1.3 cm) sticking past the middle of the finger.
- Wrap the long end around the finger once, so it comes back over the top and crosses the short end.
- Pinch the spot where the two layers overlap on top of the finger. Keep it snug but not tight. Paper doesn’t stretch, so leave enough room to slide the ring over your knuckle.
Step 3: Wrap the Tail to Lock It
- Keeping your pinch in place, take the long tail and wrap it around the overlapping layers, going around the band (not around the finger).
- Keep wrapping, laying each coil right beside the last one, until there’s about 1/2 inch (1.3 cm) of tail left. You’ll usually get three to five coils.
- Tuck the end of the tail under the last coil. Push it through with a fingernail if it’s snug.
The coils hold the overlap together and cover the short starting end. Together they form the ring’s decorative top.
Step 4: Shape and Finish
- Slide the ring off the finger, or leave it on if it’s for you.
- Gently squeeze the wrapped top to flatten and tighten the coils.
- To round out the band, slip the ring over a marker or lip balm tube that matches the finger size and roll it lightly.
Sizing Tips
- For kids’ fingers, the band will have more tail left over. Just make more coils. It makes a chunkier top, which kids usually like.
- For larger fingers and thumbs, more of the band goes around the finger, so you’ll get fewer coils, usually two or three. That’s still enough to lock the ring.
- If it’s for someone else, size it on a finger of yours that’s about the same size, or wrap it around a marker or tube of about the right thickness.
Variations
- Wider band. Stop at Step 1, part 4, for a 5/8-inch (1.6 cm) band. It has a bolder look, but each coil uses more length, so you’ll get fewer coils on top.
- Choose what shows. The outside of the band shows a quarter of one side of the bill. Try folding the band with the bill flipped over or turned end for end to change which printed details end up on the outside.
- Bigger value. Fold the ring from a $5, $10 or $20. Every U.S. bill is the same size, so the steps are identical.
- Bezel ring. Once you’re comfortable, look for instructions for the dollar ring with a square top that frames a “1.” Many money-folding books include one.
Troubleshooting
The coils unravel. The tail wasn’t tucked far enough. Push the end farther under the last coil, or add one more coil before tucking.
The ring is too tight. Unwrap the coils, loosen the band around the finger and wrap again. It’s easier to size it a little loose and squeeze the top tighter afterward.
The band is lumpy. The lengthwise folds weren’t lined up. Unfold the bill and refold, matching the edges exactly before each crease.
For more quick money gifts, try the dollar bill heart or the dollar bill butterfly.