Money Origami

How to Fold a Dollar Bill Shirt and Tie

Fold a dollar bill into a shirt with a collar and sleeves, then fold a matching tie from a second bill and slide it under the collar. Clear step-by-step guide.

On this page
  1. Overview: What You’ll Make
  2. What You Need
  3. Part 1: Fold the Shirt
  4. Part 2: Fold the Tie
  5. Part 3: Put the Tie on the Shirt
  6. Tips and Variations
  7. Troubleshooting
  8. FAQ

Overview: What You’ll Make

The dollar bill shirt is one of the best-known money folds. You fold one bill into a narrow strip, shape a collar at one end and small sleeves at the other, then fold the sleeve end up under the collar. A second bill becomes a tie that slides under the collar points.

The finished shirt is about 1 1/4 inches wide (2 inches across the sleeves) and 2 inches tall (3.3 by 5 cm). Allow 15 to 20 minutes the first time. The sleeves are the trickiest part.

If you’ve never folded money before, the dollar bill origami basics explain how to prepare a bill and make crisp creases.

What You Need

  • Two crisp bills: one for the shirt, one for the tie
  • A hard, flat surface

The side of each bill that faces down at the start ends up on the outside of the shirt and tie. For a matching set, start both bills the same way up.

Part 1: Fold the Shirt

Make the Strip

  1. Crease the center. Lay the first bill flat with the long side horizontal, the side you want on the outside facing down. Fold it in half lengthwise, bringing the bottom edge up to the top edge. Crease and unfold.
  2. Fold the edges to the center. Fold the top and bottom long edges to the center crease. You now have a strip about 1 1/4 inches (3.3 cm) wide with two flaps meeting along the center.
  3. Turn the strip upright. Rotate it so it’s tall and narrow, with the flaps facing you. The center seam where the flaps meet will look like the front of a button-up shirt.

Fold the Collar

  1. Turn it over so the flaps face away from you.
  2. Fold the top corners to the center. Fold the top left corner down so the top edge lies along the center line. Repeat with the top right corner. The top of the strip is now a point, and the triangle is about 5/8 inch (1.6 cm) tall.
  3. Turn it back over so the flaps face you again.
  4. Fold the point down. Fold the pointed top down toward you along the horizontal line where the triangle begins (the line joining the two side corners). The top edge is now straight. The two small triangles you folded in Step 5 now face you, meeting at the center and pointing down. These are the collar points.

Fold the Sleeves

Go to the other end of the strip. Each flap’s inner bottom corner sits at the center seam.

  1. Fold the right sleeve. Fold only the right flap, not the layer underneath. Make a diagonal fold that runs from the bottom right corner of the strip up to the center seam, about 1 1/4 inches (3.3 cm) above the bottom edge. As you fold, the flap’s corner swings out past the right edge of the strip, forming a small triangle. That’s the sleeve.
  2. Fold the left sleeve. Repeat on the left flap, so the two diagonal folds meet at the same point on the seam.

Lift the flap slightly with a fingernail if it’s hard to fold one layer on its own.

Fold Up the Body

  1. Fold the bottom end up. Fold the sleeve end up toward you and slide its edge under the collar points. Push it up until the sleeves sit just below the top edge, like shoulders. Crease the new bottom fold firmly.
  2. Shorten the shirt. The shirt is a little long at this point. Fold the bottom edge behind (a mountain fold) so the shirt is about 2 inches (5 cm) from the top of the collar to the bottom fold.

The shirt is done. The sleeves should stick out on both sides just under the collar.

Part 2: Fold the Tie

  1. Make a narrow strip. Turn the second bill so it’s tall and narrow. Fold it in half lengthwise and unfold, fold both long edges to the center crease, then fold the strip in half along the center. You’ll have a strip about 5/8 inch (1.6 cm) wide.
  2. Make the point. At the bottom end, fold both bottom corners behind so they meet at the center line. The bottom of the tie is now a point.
  3. Shorten the tie. Fold the top end down behind by about 2 inches (5 cm). Then fold the new top down behind by about 2 inches again. The tie is now about 2 inches (5 cm) long.
  4. Shape the knot. Fold the two top corners behind in small triangles, so the top of the tie is narrower than the blade, like a knot.

Part 3: Put the Tie on the Shirt

  1. Slide the top of the tie under the collar points, centered on the shirt.
  2. Push it up until the collar points overlap the knot.
  3. Press the collar points down flat over the tie.

The tie is held in place by the collar, so there’s no need for glue or tape.

Tips and Variations

  • Bow tie instead of a tie. A bow tie looks great under the collar. See how to make an origami bow tie with a dollar bill, and follow its note on folding a smaller bow that fits the shirt.
  • Mix denominations. Fold the shirt from a $1 and the tie from a $20, or the other way around. U.S. bills are all the same size, so the pieces still fit together.
  • A card for Dad or a grad. The finished set is flat, so it fits in a standard greeting card. Shirt-and-tie money folds are popular for Father’s Day, graduations, job celebrations and retirements.
  • Practice first. Cut printer paper to 6 1/8 by 2 5/8 inches (156 by 66 mm) and fold a practice shirt before using real bills.

Troubleshooting

The collar won’t lie flat. Re-crease the fold from Step 7 firmly, and press the collar points down with a fingernail. Tucking the body under the collar (Step 10) also helps hold them down.

The sleeves are uneven. The two diagonal folds didn’t meet at the same point on the center seam. Unfold both sleeves and refold them to the same spot.

The body won’t stay tucked under the collar. Push the bottom end up a little farther so more of it sits under the collar points, then re-crease the bottom fold.

The tie is too long. Make the folds in Step 3 of the tie a little deeper, or add one more fold behind.

FAQ

Can you fold the shirt from a single $1 bill?

Yes. The shirt itself uses one bill. The tie in this version uses a second bill, which also adds to the gift. If you only want to use one bill, the shirt still looks good without a tie.

How do you fold a $1 bill into a shirt without the tie?

Follow Part 1 on its own. You’ll get a shirt with a collar and sleeves. For a different look, slide a small folded bow tie, a ribbon or a decorative paper strip under the collar instead.

What other money folds go with a shirt and tie?

A dollar bill owl pairs well with a shirt for graduations. For a wedding card, a dollar bill heart is a popular companion.

The complete guide to money origami

Dollar Bill Origami: Easy Money Folding Instructions
Read the guide

Keep exploring

Guides from other topics

All topics →