Math and Science

How Many Times Can You Fold Paper in Half? The Math Behind the Limit

Most paper stops at about 7 folds, but the limit is a myth. See the exponential math, Britney Gallivan's 12-fold record and formula, and how to beat seven.

On this page
  1. The short answer
  2. Why the number grows so fast
  3. What actually stops you
  4. Britney Gallivan and the 12-fold record
  5. Later attempts
  6. Single-direction vs alternate-direction folding
  7. How to beat seven folds at home
  8. Why this matters in origami

The short answer

An ordinary sheet of printer paper can usually be folded in half about 7 times, sometimes 8 with effort. But there’s no fixed limit. The number depends on how thick the paper is, how long it is and how you fold it. In 2002, high school student Britney Gallivan folded a single long strip of thin paper in half 12 times, which disproved the popular claim that paper can’t be folded more than seven times.

The reason ordinary paper gives up so quickly is exponential growth: every fold doubles the thickness and halves the length you have left to work with.

Why the number grows so fast

Layers and thickness table

Each fold doubles the number of layers. After n folds you have 2ⁿ layers. Standard printer paper is roughly 0.1 mm thick, which gives these figures:

Folds Layers Approximate thickness
1 2 0.2 mm
3 8 0.8 mm
5 32 3.2 mm
7 128 1.3 cm
8 256 2.6 cm
10 1,024 10 cm
12 4,096 41 cm
15 32,768 3.3 m
20 1,048,576 about 105 m

At the same time, the footprint shrinks. Folding an A4 or letter-size sheet seven times in alternate directions leaves a stack of 128 layers roughly the size of a large postage stamp, and it’s more than a centimeter thick. You’re trying to bend a small, thick block, not a sheet.

Folding to the Moon

A favorite classroom calculation asks how many folds it would take for paper 0.1 mm thick to reach the Moon. The answer is 42 folds. 2⁴² is about 4.4 trillion, and 4.4 trillion × 0.1 mm is roughly 440,000 km, which is more than the average Earth–Moon distance of about 384,000 km. Of course, it’s physically impossible. It simply shows how quickly doubling gets out of hand.

What actually stops you

Three things combine to stop you:

  1. The paper runs out of length. Every fold uses up some paper in the curved bend, and that bend gets bigger as the stack gets thicker. Eventually there isn’t enough flat paper left to make another fold.
  2. The force needed grows. Bending a thick stack takes much more effort than bending a single sheet, and fingers can’t press a 1 cm block flat.
  3. The layers fight each other. On the outside of a fold, layers have to travel further around the bend than those on the inside. In a thick stack, the outer layers stretch or tear and the inner ones bunch up.

Britney Gallivan and the 12-fold record

In 2002, Britney Gallivan, then a high school student in California, took on a challenge to fold paper in half 12 times. She treated it as a math problem first. Instead of trying harder with a normal sheet, she worked out how long a strip of paper would need to be to survive 12 folds in the same direction, then got paper long enough. She used a very long roll of thin paper, reported at about 4,000 feet (roughly 1.2 km), and completed the 12 folds with help over several hours.

Her formula

Gallivan derived an equation for the minimum length L of paper needed to fold a strip of thickness t in half n times, always in the same direction:

L = (π × t ÷ 6) × (2ⁿ + 4) × (2ⁿ − 1)

The key takeaway is in the (2ⁿ + 4) × (2ⁿ − 1) part. For large n, that’s close to 2²ⁿ, or 4ⁿ. So each additional fold needs about four times as much paper as the previous one, not twice as much.

What the formula says about printer paper

Plugging in t = 0.1 mm (typical printer paper) gives the minimum strip length for each number of folds:

Folds Minimum length (0.1 mm paper)
7 about 0.9 m
8 about 3.5 m
9 about 14 m
10 about 55 m
11 about 220 m
12 about 880 m
13 about 3.5 km

This explains why a letter-size or A4 sheet, under 30 cm long, stops around 7 folds. To fold it once more in the same direction, you’d need a strip several meters long. It also shows why each new record has been so hard to set.

Later attempts

Since Gallivan’s record, others have tried for more:

  • The TV show MythBusters tested the claim in 2007 with a very large sheet. They got well past seven folds, with mechanical help for the final folds.
  • In 2011, a group of students in Massachusetts reported folding a very long strip of toilet paper 13 times, laying it out along a long university corridor.

As far as we know, nobody has reliably gone much beyond this, because each extra fold needs roughly four times as much paper and the stack becomes very hard to handle.

Single-direction vs alternate-direction folding

The direction you fold makes a difference.

  • Single direction means always folding the same way, like folding a long strip of paper in half end to end. This is what Gallivan’s formula describes. You need a very long, narrow strip.
  • Alternate directions means turning the paper 90° between folds, the way most people fold a sheet. The footprint stays roughly square, but each fold has to bend through a stack that’s both thick and short in both directions. Gallivan also worked out a version of her formula for this case.

For a typical sheet of paper, alternating directions usually feels easier for the first few folds because the paper stays compact. To get large numbers of folds, though, record-setters have used long strips folded in one direction.

How to beat seven folds at home

If you’d like to try for eight or more:

  1. Use thinner, larger paper. Tissue paper, gift wrap or a large sheet of newspaper all work better than printer paper. Thin, large paper is better on both counts.
  2. Try a long strip. A roll of toilet paper, register receipt paper or a strip of gift wrap several meters long lets you fold in one direction. Use the table above as a rough guide to how long it needs to be.
  3. Fold carefully. Line up the ends exactly each time. A crooked fold wastes length.
  4. Flatten each fold. Press firmly along the crease, or have helpers walk along it on a long strip, before starting the next fold.
  5. Count accurately. Write down each fold as you make it. It’s surprisingly easy to lose count around fold six.

This is a great classroom activity for exponents and measurement. Students predict the layer count, measure the thickness and compare it with the 2ⁿ prediction.

Why this matters in origami

Origami folders run into the same problem every day. Every fold adds layers, and models with many layers stacked at one point become thick, bulky and hard to shape. That’s why paper choice matters for complex models, and why designers think about where the layers will end up. It’s also an example of how a simple folding question leads to real mathematics, a theme we explore in mathematics through origami. For folding precision used to solve a classic geometry problem, see how to trisect an angle with origami.

The complete guide to math and science

Mathematics Through Origami: Geometry You Can Fold
Read the guide

Keep exploring

Guides from other topics

All topics →