What a Kusudama Is
A kusudama is a ball made by joining many identical paper units. The name is usually translated from Japanese as “medicine ball.” Early versions are often said to have held fragrant herbs or incense. Today they’re mostly decorative, hung from ceilings, used at weddings and parties, or given as gifts.
The classic kusudama flower ball is made of 60 square sheets. Each square becomes a petal, five petals form a flower, and 12 flowers form the ball. Unlike the triangle-piece method in our 3D modular origami guide, this kusudama is held together with glue.
What You’ll Need
- 60 paper squares, all the same size. Origami paper (kami) works well. So does lightweight patterned paper.
- Size: 7.5 cm (3 inch) squares are a popular choice for a ball you can hold in your hand. Larger squares make a bigger, showier ball, and smaller squares are fiddlier.
- Glue: a glue stick or a small amount of white craft glue. Quick-grab craft glue makes assembly easier.
- Clothespins or paper clips to hold flowers while the glue sets
- String or ribbon for a hanging loop, plus an optional tassel or bead
For color, try one color per flower (12 flowers in two to four colors), or all petals in one solid color.
How to Fold One Petal
Repeat these steps 60 times.
- Fold a triangle. Place the square colored side down. Fold it in half diagonally, with the long folded edge at the bottom and the point at the top.
- Make a diamond. Fold the left and right bottom corners up to meet the top point. You now have a small diamond (a square standing on one corner).
- Fold the flaps in half. On each of the two front flaps, fold the edge that sits on the center line outward so it lines up with the outer edge of the diamond.
- Squash fold. Open each of those flaps slightly, then press them flat so they spread into a kite-like shape. This is called a squash fold.
- Fold down the tips. Small triangular tips now stick up above the top edge of the squashed flaps. Fold them down so the top edge is level.
- Fold the squashed parts in half again. Fold each squashed section back along its center crease, so the folded edges meet in the middle.
- Glue into a cone. Put a little glue on one outer face of the folded flaps, then curl the petal so the two outer faces meet and stick. You get a cone-shaped petal with a neat folded center.
The first petal takes a while. After a dozen or so, you’ll be much faster.
Making a Flower From Five Petals
- Put a thin line of glue along one side of a petal.
- Press a second petal against it so their points meet at the bottom.
- Add the third, fourth and fifth petals the same way, closing the circle by gluing the fifth petal to the first.
- Hold the flower with a clothespin or paper clip until the glue sets.
Make 12 flowers. Let them dry fully before moving on.
Assembling the Ball From 12 Flowers
The flowers are joined so that each one touches the flowers around it, petal to petal.
- Make the first half. Take one flower as the center and glue five flowers around it, one against each of its petals. Glue each outer flower to its neighbors as well. This forms a dome of six flowers.
- Make the second half the same way, with the remaining six flowers.
- Add the hanging loop (see below) before closing the ball, if you’re using one.
- Join the halves. Put glue on the touching petals around the rim of one half and press the two halves together, rotating slightly so the flowers fit into each other’s gaps.
- Hold it while it dries, using clips or a rubber band around the outside if needed.
Adding a Hanging Loop and Tassel
- Thread a ribbon or string through the center of one half before closing the ball. Knot it inside, or tie it to a bead so it can’t pull out.
- For a tassel, thread it onto the same string so it hangs below the ball, or glue it into the gap between flowers on the bottom.
- Choose a ribbon that matches the paper colors. A satin ribbon gives a neat, traditional look.
Tips for a Neat Finish
- Crease sharply. Crisp petals hold their cone shape and line up better.
- Use glue sparingly. Too much glue soaks the paper and leaves shiny marks.
- Keep all squares the same size. Even small differences leave visible gaps.
- Shape before gluing the halves. Gently press both domes into a rounded shape so they meet cleanly.
- Add centers. Small beads, punched paper circles or tiny stamens glued into the middle of each flower add a decorative finish.
Glue-Free Kusudama Options
If you’d rather avoid glue, many kusudama designs are made from interlocking units instead. Sonobe units are a common starting point. Six units make a cube, 12 make a star-like shape, and 30 make a spiky ball. These are a different style from the flower ball, but they use the same idea of building a 3D shape from many identical pieces.
If the modular process appeals to you, the triangle-piece method is another way to build big 3D forms without glue. See our guide to folding a 3D origami unit or start with a 3D origami swan.
Troubleshooting
- Petals come unglued: let the glue get tacky for a moment before pressing, and hold the joint for a few seconds.
- Gaps between flowers: press neighboring flowers together firmly while gluing, and check that every flower has exactly five petals.
- The ball looks lopsided: make sure each half really has one center flower with five around it, and line up the halves before the glue sets.
- Petals look flat instead of cone-shaped: the final curl in step 7 may be too loose. Overlap the outer faces fully before gluing.